Will.i.was Prerunner Build

Current state:

11/26/23
Long story. Flipped it and swapped cab. Lots of mods + supercharger since then. Front end swap with custom retrofitted morimoto d2s 5.0 and tid bits. Fiberglass and lt in the works. 4x4 transmission upgrades and twin stick about to be installed. Rough current progress.



5/22/2021
35's, FJ t-case, Lights, URD LT Spec-U Headers, some other shenanigans. lots of stuff installed and/or laying around




As of 7/29/2020
Lots of water in headlight, excuse the haziness. It clears up in a day


Previous:


Previous state:













Suspension:

(Full suspension refresh with new LCA, inner/outer tie rods
Full brake refresh with brembo blanks and pads)

Front
Bilstein 5100 w/ Eibach 725lb pro lift kit springs set @ 2nd clip
KYB tophats
Freedom off-road UCA
1/4" polycarbonate driver spacer
Mevotech swaybar endlinks
Energy suspension polyurethane swaybar bushings
Swaybar relocation kit
SPC cam alignment bolts
Reinforced cam alignment plates
Front reinforcement plates
Relentless front bumper reinforcement bracket
Marlin crawler LCA gussets


Rear
Bilstein 5125 33-104645 15.91"/25.89" mounted with eyelet adapter
2" cast iron tapered blocks -> icon rxt AAL
3 degree shim/CB drop
Spicer greaseable ujoints
Front and rear wheelers superbumps
+4" rear wheelers brake lines
1" driveline spacer


Wheel/tires:
Enkei RPT1 Bronze 16x8 0et with front 1.25" spacer
Falken Wildpeak AT3W LT285/75R16 -> Toyo Open Country AT3 LT315/75R16


Exterior:
Honeycomb grill w/ matte black emblem -> "TRD POO" Grill
Bushwhacker fenders DIY painted with black hardware and custom painted mudflaps
Black plastidipped emblems
BHLM OEM headlights + Morimoto D2S 5.0 + Panamera 2.0 shrouds
Led interior lights
Diode dynamics SS3 SAE fog white
Baja Design S1
Baja Design Squadron Sport
Cali Raised 43" Amber/White LED bar
Tacomabeast led tail lights
Led 3rd brake light
Paint matched rear bumper with flush mount led
Paint matched side mirrors
Cali raised bed mounts with auxbeam side shooter led
Cali raised front lo pro light mounts with auxbeam side shooter
2" hitch receiver
DIY CMC and pinch weld
Black painted wheel hubs and rear drums
Black painted exhaust
Chopped exhaust @ axle
AVS flush window deflectors
Bed D-rings
Flag pole holder
Cali raised low profile bedrail brackets
3M 1080 Matte Black Wrapped Roof
Hookeroad Roof Rack
OVS Nomadic 180* Awning
Hookeroad lockable rear cubbies


Engine:
3* cam gears
Deleted intake mesh filter
Volant intake w/ ram air scoop
URD MAF calibrator
Exhaust axle chop
1" Intake manifold spacer


Armor:
Victory 4x4 sliders
Beaver tail hitch
Coastal Offroad High Clearance bumper (90hrs welding)

Electronics:

$124 Anytone AT778UV AnyTone AT-778UV Dual Band Transceiver Mobile Radio VHF/Uhf Two Way Radio

Anytone AT778UV dual band ham radio hardwired - mfj 62" or tram 38"
Midland 75-882 cb hardwired - 5' NGP firestik mounted on ceiling
Hella horns + hella air horns with selector switch
Blaupunkt 1200w amp and 12" subwoofer stealth box
Plenty of CH4x4 switches

$150 Rexing V1P 4K Car Dash Cam 2.4" LCD 2160p Front + 1080p Rear Wi-Fi 170° Wide Angle Dual Channel with Rear Cam, G-Sensor, WDR, Loop Recording Mobile App Supercapacitor

Rexing V1P front and rear cameras hardwired
Power sliding rear window
ABS delete mod
Compustar cm7900 with remote start DIY installed (Blade AL)
Fog light on with high beam mod
Rexing front and rear 1080p camera with SanDisk 128gb high endurance microsd
Zesuper 9500lb winch


Interior:
Pioneer AVIC Z150BH headunit
MESO upper molle rack
Ballsout off-road mounts with RAM and custom scosche mount for radios
Scangauge 3d printed housing & Scangauge II w/ custom Xgauge configs
Broadway Wide rear view mirror
Upper windshield tint
Passenger seat mounted fire extinguisher
Passenger mounted road flares
IFAK/emergency gear mounted on molle panel
Cam lock center console
Dome light on when doors open mod
Motorized rear slider window
Discreet pistol and rifle mounts

 

Subbed, love the build man

 

Man those are the best looking wheels I've seen lately! I'm kinda stuck on stock steelies but yours make me want.

 

Thanks for the kind words. More things to happen soon!

 

Added a picture of the current status.

Alot of parts and fabrication added in the last few months. Will update with a narrative soon!

 

Jeebus I cannot keep up with thread and the mods that occur. Alot is done every week. I will update current photos and expand on mod list once I "get" some free time

 

Threw on some 2" wheel spacers and 4x4 conversion parts.

 

Hey, I'm new here and looking for how you think the ride quality changed after adding the spacers? I just got the Eibach 2" level shocks and kind of want to add spacers for some more offset, but also hear that it messes with ride quality. What do you think? Edit, also your truck looks great!

 

As long as the spacer is hub centric you won't have any issues with reliability, our vehicles utilize a 106mm center bore (more accurately it's 106.1mm).

1.25" is typically what people run to clear suspension components and for cosmetic purposes.

I do believe the spacer impacts the overall comfort but very minimally. The wheels are pushed out further and with more distance from the original position, causes the ride to be a bit more harsh.

Thanks for the compliment, it's been a few years in the making and alot of frustration getting it where it is now lol

 

Did you already finish the conversion to 4x4 or you are still working on it?

 

I currently only have the front differential, axles and wheel bearings installed.

The only component I am missing is the transmission at the moment.

The only other thing is fabricating and welding up the new crossmember. I initially planned on modifying the stock cross member and hacking it up. I have seen some good ideas on here lately though and will probably weld up an entire tube steel crossmember with the proper transmission mount dimensions for additional strength.