What Have You Done To Your 2nd Gen Tacoma Today?

Brought this home yesterday ,tows and handles like a champ.

 

Will do! I almost cracked open the front diff to put in a Lokka but didnt like the idea of clacking when turning and front driveshaft spinning all the time

 

If you get your hands on an oem foglight switch, you can just remove the blank for where it normally goes on the left side of the dash. The harness should be behind the blank like mine was ( 2009 base 4x4). I just plugged the oem switch in and went to the bumper and removed the foglight covers, and the aftermarket foglight housings bolted in perfectly. The oem wiring should be tucked somewhere right above the foglight openings on each side.

 

So no wiring from the fuse box to the cabin switch ?

 

i didn't have too. It was all pre wired. Toyota likes to do that.

 

Thanks All!

 

I'd be curious as to how tough the install is. Particularly the front. Gonna be doing 4.88 and a rear ARB in a few months and trying to decide if I want to go the same route you are or just pay to have it all installed.

 

Digging that rear bumper. Pretty much sold on that's the one I gotta get.

 

CaliRaised bed bars, Tepui Kukenam 3, and Diode Dynamics SS3s. Bring on Summer!

 

The rear is gonna be pretty simple to swap. The front will be a little more involved but I put the other carrier in when I did the 4x4 conversion so i know what's involved. Probably take me a full day to do both.

 

On our trucks, the relay for the cigarette lighters is behind the fuse panel. Undo three 10mm nuts and you can move the panel forward enough to get to it. Pop it out, and take the cover off. Solder the connections and reinstall. Now you’ve got always on cigarette lighters! Just did this today so I can power my fridge in the back seat.

 

Being electrically challenged, I would need a little more info, which wires and where to solder them. Thank you!

 

See quote below. Nothing involved with wiring at all, only the relay itself.

 

You won’t be disappointed. The design of the legs and how it mounts to the truck is pretty freaking stout. I’m stoked on it for sure. And he’s doing a tax sale right now. 20% off.

 

Just added a skid plate and exhaust tip! Really excited to add more to my 2013 off road. Let me know if you have any ideas on what I should do next.

 

Vaccumed and washed some winter salt and mud off

 

Looks like you will be soldering closed the ACC SKT Relay, Pin 3 and Pin 5. Thanks for the info @EatSleepTacos

 

Trail edition wheels
Baja mtz p3 285/70r17

 

Finally started sound deadening in cabin.

Installing Media Panel in the center console. Connections - HDMI Media input, USB Media input, AUX input, USB 5volt, 2.4Amp output

Installing another media panel in the back of the center console. Connections - HDMI Output, 3.5 Headphone Jack, USB 5volt, 2.4Amp output, USB Media Input.

Cocoon GRID-IT! Accessory Organizer & Vehicle OCD - Center Console Organizer

Does anyone know what this is?

$26 Axxess AX-FDUSBAUX USB/AUX/HDMI Knockout Replacement Panel for Select Ford Vehicles

2 of Axxess AX-FDUSBAUX USB/AUX/HDMI Knockout Replacement Panel for Select Ford Vehicles

$17 Cocoon CPG5GY GRID-IT!® Accessory Organizer - Small 10.25" x 5.125" (High-Rise Gray)

Cocoon CPG5GY GRID-IT! Accessory Organizer - Small 10.25" x 5.125" (High-Rise Gray)

$20 Vehicle OCD - Center Console Organizer for Toyota Tacoma (2005-2015) - Made in USA - SLX100

Vehicle OCD - Center Console Organizer for Toyota Tacoma (2005-2015) - Made in USA