Whoring out ECGS bushing tool

I'm sending mine out to Newlife. He'll send it to the next person that needs it.

It's ugly but worked great for me. I made it after the stores were closed with what I had laying around. I may have been in a hurry and used the wrong pitch tap, and then may not have had a fine thread bolt long enough. So there's a 12mm coarse thread bolt with the flats on the head ground off and fine threads put on it poorly. Laugh at the idiocy, marvel at the ingenuity. lol

The flat side of the puller goes toward you. Wiggle it a little as you're putting tension on it. That will seat it only on the bearing, I think there's a little lip in the diff case it can get caught on. And freeze the bushing to shrink it before you start to reinstall. Mine was very tight trying to get it in.

For an install tool I've always used a big 1/2in drive socket with an extension put into it backwards (slide the extension into the socket where a nut would usually be).
But I just got these and love them.

$41 DASBET 52 in 1 Custom Bushing Driver Tool Set | Transmission Bushing Driver Removal Set Wheel Axle Bearing Race and Seal Installer Tool Kit Custom Bushing Bearing & Seal Driver Set 18mm-65mm

https://www.amazon.com/gp/product/B06ZYH34JZ/ Two of the disks stack, one that slips in the bushing to center it and then one that goes on the lip of the bushing to push it in. Autozone should loan you a similar kit.


I'll get it in the mail and you should have it next week.

 

@Newlife

Sent it out last week.
Should show up about now.
Did you get it?

 

Yes got it today I think. I haven’t opened it yet. I got some rando package Saturday too I haven’t opened. I’ve been so busy getting reports done at work and making sure I have every little piece of my truck ready for this swap....

 

I have @TacoMa oh7’s tool and ready to ship. Heading to Usps tomorrow on lunch if anyone needs it

 

Pass that ugly POS on eventually with what's going on. post here to keep track, but really IDC.

EVERYONE ELSE...STAY THE FUK HOME.

I've got a friend that's a doc, they told me some scary stories, and they are preparing to weather the storm... Stay the fuk home again, and for a third refrain...

Use the calories in your cupboard and wait till they're bare. Whatever date that is. Don't go buy 4 things at the store.

Thx

 

@Newlife Still holding that tool?

DM me if you do.

 

Sent message.

 

Lmk if I can be next in line. no rush. just ordered my ECGS bushing and a few other parts to arrive before Id be installing.

Thanks to @tacoma oh7 your a legend for this

 

Hey boss I just saw this. Pm me your address and I’ll get it out tomorrow. I’ve gotta take some other stuff so I’ll already be there.

 

Pmd you

 

Heading to you tomorrow.

 

Sweeeeet thanks man

 

Hey toy:

Paste this to whomever you send it to when you're done with it:
"
Paste this to whomever you send it to when you're done with it:
After you are done with it:
Post at https://www.tacomaworld.com/threads/whoring-out-ecgs-bushing-tool.630638/page-3#post-23103286 that you have it available.
Keep it till someone needs it and pay to ship it to the next guy.
Keep this going, don't let it stall out with you. send it to @tacoma oh7 if you're not able to post it to the next guy, for reasons
Pay it forward.
"

copy that and pm it to the next.

With my most sincere regards, sir









Oh ya, and, STAY THE FUK HOME!!!! luv u all don't kill people

 

Officially out of Tennessee and on its way to @07tacomatoy .. it served us well here in East TN

 

Thank you @tacoma oh7 & @Newlife - will lyk when it arrives

 

Any chance of this Heading North to Canada? Need one. Thanks.

 

I just ordered a bushing Sunday, but I picked up an ecgs removal tool off eBay two weeks back. I should be getting this bushing taken care of this weekend, and throwing another tool out for the whoring.

 

Can the whore make her way to Canada?

 

I plan on doing mine in a couple weeks if anyone has a tool free?

 

Well, apparently it was a one time use tool lol. I got mine done this afternoon, but the threaded puller side bent right at the threads and now its stuck. I'll try to straighten it at work on Monday, but I'm not holding out much hope......