What Have You Done To Your 2nd Gen Tacoma Today?

Swapped my Bestop clamps for this new design. They really clamp down on the side rails to hold it tight compared to the old style. Old ones also scuffed the bedside molled panels as seen circled below.

 

Are you regeared? Those have to be heavy as hell....

 

Are these the same ones @kidsmoke recommended? Thinking about doing this too but I haven't had any issues with the old style.

 

Yep

 

New grille is coming back from Paint this Friday. pretty psyched

Primary Color: Silver Streak Mica (1E7)
Secondary: Magnetic Gray Metallic (1G3)
3rd: Black Sand Pearl (209)

 

What tail lights are those pls?

 

wow wish I could trade in the other trd pro grill that i have for this style one. You have a link for this one?

 

I attempted to replace my broken converter heat shield.
I removed the old parts and needed help to get the front clamp on. He said the threads were started so I tightened it by hand and the bolt broke.
The bolt was cross threaded. I had to go back to Toyota and buy a new clamp and bolt.

 

Put the first blemish, that I’m guilty of, on my ‘15 today....Was helping my mom get mulch for some of her landscaping and took the 4 wheeler to get another shovel. Tried to squeeze between the tailgate and the embankment on an off cambered, weird angle. Looked like I had plenty of room. Unfortunately, my dads brand new can am outlander took the brunt of it. This mistake will cost me a couple hundred dollars. Thinking I will try to get a can of color matched paint just to keep it from rusting. Not too noticeable otherwise.

 

Just added a little bit of bling by adding a new antenna, AMI Big Stick, 9" that I spotted over at AutoAnything while getting my air filter last week.

 

Tomorrow will be another couple of firsts for my new to me ‘15. First forrest service road, first time camping, first time airing down, first time sleeping in the bed. Lots of firsts!

 

Only because I still don’t have my first gen’s regear done.

 

Over the yrs I've nicks, dents &scratches everywhere from using it as truck. The taco wears them proudly too!

 

I don’t always talk to myself, but when I do, I quote myself on TW!

 

Out with the old and in with the new. Diode crapped out in my 100 amp alternator so I replaced it with a remanufactured Denso 130 amp one. $170 and 45 minutes later and no more squealing sound under my hood! Outside of regular maintenance, this is the only thing I've *had* to replace on my 2013 DCSB (she's a hair under 98k miles)

 

Bought some eye bolts, lock washers, washers and the t-thingy for the rails. Had to cut about 1.5” off the eye bolt for a better fit. Now I can attach my cargo net more proper. Works great when hauling a bunch of tubes to go floating. 3/8 for the bolt in case anyone wants to know. Then hit it with some satin black paint although eye bolts were black, just a little more protection


ok so I can’t turn the picture 180 degrees so now it’s upside down. But you get the point I hope

 

Typically when I talk to myself, I’m saying, “What the f***!”

 

https://www.alibaba.com/product-detail/offroad-part-ABS-plastic-black-refit_62411707954.html

 

Added some D rings on the bolts for the tailgate. I’m not going to be using these to tie down heavy loads, mainly for my cargo net to keep things from flying out. Also added some 550 cord for extensions since this cargo net is so short, got the net free. So not a bad investment so far

 

Added some Silverado bumpstops.

lot cheaper than timbrens for my broke ass. Other members have done the dirty work and sounds like they’ll hold up just fine.