Toyota spec. list IMPORTANT

Useful content: the thread
(please correct or add to this as necessary, and ALWAYS double check if you arent sure!)
(This is an ongoing work I have compiled from any and all sources Either direct from Toyota™ or otherwise)

Nut & Bolt Sizes
-Front Top Hat Nut: M10x1.25 (Qty.6)
-Front Lower Strut Bolt&nut: M14x1.5x76 (qty 2)
-Rear strut top Nut size: M10x1.5 (Qty.2
-Rear lower strut bolt: M12x1.25x70
-Rear Shackle bolt: M14x1.5 x 100mm long.
-Front recovery hook: 12 x 1.25 x 60 mm grade 8.8 #90119-A0193
-M12-1.25 (1.75)
-front sway link m12
-license plate bolt/washer M6x1x20mm
-alignment cam m16

Toyota Part#:
Strut bolt assembly
-90105-A0113: bolt
-90178-A0058: nut
-91622-41400: washer
Suspension/Control Arm/Alignment Cam
-Upper Control Arm Nut 90080-17208 x2
-Outer Tie Rod 45046-09340 x2
-CV Dust Cap, Grease Cap

$33 43514-28010 Genuine Toyota Parts - Cap, Fr Hub Grease (43514-28010)

43514-28010 x2
-Adjust Cam, RIGHT 48409-60020 x2
-Adjust Cam, LEFT 48190-60020 x2
-Adjust Cam, LEFT 48198-60011 x2
-Bolt W Washer 90119-A0166 x2
-Control Arm Nut 90178-A0001 x2
-Front Strut Lower Bolt, Bolt Flange 90105-A0113 x2
-Front Strut Lower Nut, Gear Assembly Nut 90178-A0058 x2

TORQUE SPECS
Engine:
Throttle body mounting nuts/studs: 13 ft-lbs
Spark plug: 14 ft-lbs (2RZ/3RZ), 13 ft-lbs (5VZ)
Oil drain plug: 27 ft-lbs
Engine mount to frame: 28 ft-lbs
Engine mount to block: 38 ft-lbs (2RZ/3RZ), 32 ft-lbs (5VZ)
Head bolts: 29 ft-lbs + additional 90° + another 90° (2RZ/3RZ)
Head bolts: 25 ft-lbs + additional 90° + another 90° , recessed 13 ft-lbs (5VZ)
Main bearing caps: 29 ft-lbs + additional 90°(2RZ/3RZ), 45 ft-lbs + additional 90° (5VZ)
Exhaust manifold: 36 ft-lbs (2RZ/3RZ), 30 ft-lbs (5VZ)
Intake manifold: 22 ft-lbs (2RZ/3RZ), 13 ft-lbs (5VZ)
Air Intake Chamber: 15 ft-lbs (2RZ/3RZ), 13 ft-lbs (5VZ)
Crankshaft pulley bolt: 193 ft-lbs (2RZ/3RZ), 217 ft-lbs (5VZ)
Oil pan bolts: 9 ft-lbs
Rear main oil seal: 9.7 ft-lbs
Rear end plate: 14 ft-lbs
Starter mounting bolts: 29 ft-lbs
Pressure plate to flywheel: 14 ft-lbs
Flywheel to crankshaft bolts: 65 ft-lbs (2RZ), 19 ft-lbs + additional 90° (3RZ), 63 ft-lbs (5VZ) ~USE LOCTITE~
Flexplate to crankshaft bolts: 54 ft-lbs (2RZ/3RZ), 61 ft-lbs (5VZ)

FRONT:
Brake caliper mounting bolts: 90 ft-lbs
Brake caliper banjo bolt: 22 ft-lbs
Steering knuckle to lower ball joint: 59 ft-lbs ~USE LOCTITE~
Outer tie-rod to lower ball joint: 67 ft-lbs
Lower control arm to frame (alignment cams): 96 ft-lbs
Lower control arm to shock absorber: 101 ft-lbs (may vary with aftermarket equip)
Lower control arm to swaybar end link: 51 ft-lbs
Lower ball joint to lower control arm: 112 ft-lbs
Upper ball joint to upper control arm: 80 ft-lbs
Upper control arm to frame: 87 ft-lbs
Shock absorber upper mount (3 bolts): 47 ft-lbs (may vary with aftermarket equip)
Shock absorber center nut: 22 ft-lbs
Swaybar to swaybar end link: 22 ft-lbs
Swaybar brackets to frame: 19 ft-lbs
Differential front mount to frame: 101 ft-lbs
Differential rear mount to frame: 64 ft-lbs
Ring gear bolts: 71 ft-lbs
Differential drain plug: 48 ft-lbs
Differential fill plug: 29 ft-lbs
Axle shaft hub nut (ADD): 174 ft-lbs
Free wheel hub inner lock nut (manual hubs): 203 ft-lbs
Axle shaft inner hub safety bolt (manual hubs): 13 ft-lbs
Hub body to axle hub (manual hubs): 23 ft-lbs
Hub body cover (manual hubs): 7 ft-lbs

REAR:
Backing plate to axle housing: 50 ft-lbs
Shock absorber to axle: 53 ft-lbs
Shock absorber to frame: 53 ft-lbs
Axle u-bolts: 90 ft-lbs
Front leaf spring mount: 115 ft-lbs
Shackle bolts (both): 67 ft-lbs (may vary with aftermarket equip)
Leaf spring centering pin: 33 ft-lbs
3rd member to axle housing: 18 ft-lbs
(with e-locker), 54 ft-lbs (w/o e-locker)
Ring gear bolts: 71 ft-lbs (with e-locker), 92 ft-lbs (w/o e-locker)
Carrier bearing caps: 83 ft-lbs (w/o e-locker)
E-locker acutuator to 3rd member: 20 ft-lbs
Differential drain & fill plugs: 36 ft-lbs
Torque specs are 74 lb ft for bottom bolt and 15 lb ft for top nut.

STEERING:
Steering wheel set nut: 26 ft-lbs
Outer tie-rod to lower ball joint: 67 ft-lbs
Inner tie-rod to rack: 76 ft-lbs
Tie-rod end lock nut: 41 ft-lbs
Steering rack mounting clamp: 123 ft-lbs
Steering rack vertical center mounting bolt: 123 ft-lbs
Steering rack horizontal mounting bolt: 141 ft-lbs


Miscellaneous:
Seat mounting bolts to body: 27 ft-lbs
Seat belt: 30 ft-lbs (all mounting points)
Body mounting bolts: 48 ft-lbs
Conversion Factors:
1 ft-lb = 12 in-lb = 1.35582 Nm

TRD Air Filter: Part Number PTR0334140:
TRD Air Filter Clean Kit: Part Number: PTR4300088:
TRD Oil Filter: Part Number PTR43-00082 (cartridge style for 16+):
TRD Skid Plate:

$450 PTR6035190 PTR60-35190

PTR6035190:
TRD Oil Cap: PTR041210802:
TRD Radiator Cap: Part Number

$48 PTR040000003 Toyota Radiator Cap - PTR04-00000-03

PTR040000003:
TRD Floor Mat (carpet): PT206-35089-02:

3rd Gen TRD Off-Road:
Factory Wheels
Wheel: 16x7
Offset: +25
Backspace:
weight: 25lbs
Tire: Goodyear Adventure Kevlar
Size: 265/70R/16
weight: 42lbs

Engine OIL
Engine oil (0W-20 ILSAC GF-5 oil - Toyota part # 00279-0WQTE-01)
1) Check w/ engine warm greater than 5 minutes after shutting off engine
2) Tip: leave dipstick out while waiting 5 minutes to allow oil in dipstick to drain back down, makes it easier to read
3) Per manual, it’s 1.6 qts from low mark to full mark, don’t overfill

Coolant (Toyota SLLC - Toyota part # 00272-SLLC2, 50/50 pre-diluted, Canada is 55/45)
1) Between LOW and FULL lines with engine cold

Brake fluid (FMVSS No. 116 DOT 3 or SAE J1703)
1) Between MIN and MAX (should be near or at max with fresh pads)

Power steering fluid (Automatic transmission fluid DEXRON® II or III)
1) Between min and max (cold and hot lines provided)
2) Cold - not driven in last 5 hours (50-85 degF fluid temp)
3) Hot - driven 50 mph for 20 mins (140-175 degF fluid temp)

Clutch fluid (FMVSS No. 116 DOT 3 or SAE J1703)

Rotate tires - every 5k or 6 mo

Front to back/back to front on each side
Lug nut torque - 83 lb-ft (21mm)
Check torque ~1000 miles after rotating


Replace engine oil and filter - every 10k or 12 mo (severe: 5k or 6 mo)

Torque specs:
Oil pan drain plug - 30 lb-ft (14mm)
Oil filter cap - 216 lb-in/18 lb-ft (

$22 TOY640 Assenmacher Specialty Tools TOY 640 Oil Filter Socket Wrench for Toyota/Lexus

TOY640 with 15/16" or 24mm socket)
Oil filter drain plug - 120 lb-in/10 lb-ft (3/8" square drive)
No. 1 engine under cover sub-assembly - 22 lb-ft (12mm)
No. 2 engine under cover sub-assembly (off-roads) - 22 lb-ft (12mm)

Parts:
Oil - 6.1-6.2 qts 0W-20 ILSAC GF-5 oil - Toyota part # 00279-0WQTE-01
Oil pan drain plug gasket - Toyota part #

$9 90430-12031 Genuine Toyota - Oil Drain Plug Gaskets (QTY10)

90430-12031
Oil filter element kit - Toyota part #

$28 04152-YZZA1 1/2 case (QTY5) Oil Filters

04152-YZZA1

Special tools:
$18 Assenmacher Specialty Tools TOY 640 Oil Filter Socket Wrench for Toyota/Lexus
AST TOY640 filter wrench (or Toyota SST 09228-06501)
5/8” ID tubing (for oil filter drain pipe)

Tips:
1) Requires removing skid(s) for access.
2) Oil filter has permanent housing, oil filter element kit includes new filter cartridge, 2 new gaskets, and the temporary oil filter drain pipe.
3) Hose for oil filter drain pipe (if used) should be 5/8” ID (15 mm). About $1 at Lowe’s in the plumbing section for clear vinyl tubing. Can help with splashing.
4) Proper torque of the oil filter cap and oil filter drain plug should help prevent the cap coming off before the drain plug on the next change, which can be a lot cleaner.
5) When you remove the filter drain plug, give it a little impact. If you're too smooth, the plug and housing will try and move together.
6) https://www.tacomaworld.com/threads/oil-change-checklist-service-record.462476/ by @RichVT

Re-torque propeller shaft bolts - every 15k or 18 mo (severe: 5k or 6 mo)

DIFF GEAR OIL
Toyota Genuine Differential gear oil LT 75W-85 GL-5 or equivalent - Toyota part #

$50 08885-02506 Differential Gear Oil LT - 1 Liter Bottle

08885-02506
Front - 1.6 qts; Rear - 3.1-4.2 qts (varies with model)
Rear drain plug gasket - Toyota part #

$22 12157-10010 Toyota Oil Drain Plug Crushable Steel Gaskets Set of 10 OEM 12157-10010

12157-10010
Rear fill plug gasket - Toyota part # 12157-10010
Front drain plug gasket - Toyota part #

$8 90430-24003 Front Differential Drain Plug Gasket

90430-24003
Front fill plug gasket - Toyota part # 12157-10010

Manual transmission oil - inspect every 30k or 36 mo (severe: replace every 30k or 36 mo)

Torque specs:
Drain plug - 27 lb-ft (24mm or 15/16")
Fill plug - 27 lb-ft (24mm or 15/16")
Parts:
Toyota Genuine Manual Transmission Gear Oil GL-3 (GL-4) or equivalent, SAE

$30 75W-90 Synthetic Gear Lube - 1 Quart (Pack of 2)

75W-90
4 cyl - 2.3 qts, 6 cyl - 2.6 qts
Drain plug gasket - Toyota part # ??
Fill plug gasket - Toyota part # ??

Factory Alignment
FWIW, factory spec is;
+2.2 caster
+0.5 camber
+0.05 toe

 

Nice write up.

 

Liked and bookmarked. Great job OP!

 

Looks like a lot of the same information thats in the maintenance sticky?

 

I thought it might be helpful to put the Tacoma Product Information pdf files here for the years 2016, 2017, 2018, 2019 & 2020. These files include extensive details on power train, exterior features, interior features, what's standard across the trim levels, and the various Packages and Options available for each year.

Hopefully the attached pdf files will be a useful reference for 3rd gen owners or those looking to buy a new or used Tacoma.
NOTE: 2018 specs lists a 4-cylinder manual transmission, that never happened, 4-cylinder manual was discontinued for 2018, 2017 was the last year for the I4 manuals.

 

Subbing

 

Sub a dub dub

 

Sub

 

And of course no Master List would be complete without a link to the 3rd Gen Tacoma Service Manual (2016, I think the last year they published in document form), courtesy @tonered :
2016 Tacoma Service Manual Availability PDF
It's a huge file, so download might take a while.

 

What’s the TL/DR.

 

Too Long/ Didn't Read version.

 

Haha! I was being a smart ass ASKING for the tldr version.

 

Sub

 

Maybea you could add the Canadian part numbers for the following...
Toyota Super Long Life coolant 55/45: C0009-00120
0W20:
1L C0BBA-0W2SN-1L
5Qt: C0BBA-0W2SN-1J

 

our trucks like to twerk and apparently they have oil in them

 

3rd gen trd or come with goodyear adventures stock? thats awesome.

 

Should be a sticky or a link in the 3rd gen DIY maintenance section

 

anyone have the 3rd gen Haynes manual?

 

I think I have the Hayes manual. Might be the Clymer not 100% it is in a box while moving. Definitely get one but had some stuff missing or not completely clear in some sections