New Pioneer DMH-WC6600NEX flush mount install

I think it's the one with the smaller white connector block on it. I took both out to the truck and found only one would connect to anything on the truck side. That ruled out the other one! Reverse camera works fine!

 

look at page 31 it’s the one with more cables going into the black connector

 

Thanks. I knew that post was somewhere, I just couldn’t find it lol.

 

I wire things up for a living, and this is one of the most confusing things I've ever attempted lol. Does anyone have a picture of the harness with everything plugged in? Which female RCA does the yellow male RCA back up camera plug into, the brown? Also, where do the AUX input cables from the T02 plug? And the maestro "data cable." Thanks in advance.. This one is getting me right now

 

Yes into the brown there is only one receptacle on the maestro and the HU that accept the data cable

 

You have to buy another adapter that plugs into the headphone looking jack hanging off of one of the harnesses. I’ll post the Amazon link. Not 100% positive that this specific one works because I bought it plugged it in and went oh yeah i don’t even have an aux port on my dash anymore. The maestro link cable goes in the matching port on the back of the pioneer deck. There is only 1 spot it can plug into. Like the guy said above the rca for the camera is the brown one. Hope this helps.

Qaoquda 3.5mm to RCA, 90 Degree Right-Angled 3.5mm 1/8" TRRS Stereo Male to 3 RCA Female Jack Adapter Cable-8inch https://www.amazon.com/dp/B01LAJTTBU/ref=cm_sw_r_cp_api_i_z7jqFbFWY4F76

 

I am in the process of installing my head unit and I cannot get my reverse camera to work. However the aftermarket front camera is working. Does anyone have any suggestions?

 

Is this connector for the 3.5 auxiliary jack in the truck? If so, it’s something I will never use. Gonna try to finish out the install today at some point.

 

I seem to recall the yellow plugging into the brown jack for your reverse camera.

 

SOS where do these go? Gray connector comes from the left. Big white connector comes from the right. And the adaptor came in the st02 kit

 

Thanks! I’m an idiot.... I don’t think I had it plugged in all the way... now my next hurtle is trying to register the headunit and get the browser to work.

 

The installation instructions are spot on. Have you been using them?

The 3 pack of adapters you bought separate, only 2 are used. 1 is the GPS antenna which plugs into the HU. 1 is satellite radio antenna that plugs into the SXM unit if you have it.

 

http://cdncontent2.idatalink.com/co...RR-TOY/ADS-RR(SR)-TOY02-DS-IG-EN_20160224.pdf These instructions? I don’t see anything that tells me which is gps and which is satellite. I’m also out of places to plug. The big white factory plug comes from the right. The one with the adapter comes from the left.

 

Forgive me I'm at work so I can't check but the adapter you have in the picture I believe is not used.
Three adapters come with the kit:
Black cable with black connector from truck (satellite antenna) goes to adapter (teal on one end and black/gold on the other) then to Sirius tuner. (Don't need the Sirius antenna that comes with SXV300 if using antenna already in truck).
Black cable with white connector (very similar) from truck (this is GPS antenna) goes to adapter (teal one end, green on the other) and then directly into GPS port on the Pioneer radio.
Adapter with teal one end and grey the other: not used.

Don't care what others say, the instructions suck. Crutchfield is very helpful if you bought from them though, easy to get through to a real person and they can facetime your setup and walk you through it. Recommended.

 

Thank you all for the help. I finally got it in. One last thing. I’ve done the update with carav and the bypass. What do I need to do to get the time and date to set? Plus weather to load.

 

Time and date are set automatically if you have everything plugged in correctly. I had the gps and xm wires reversed and mine wouldn’t set. As soon as I plugged them it set and works just fine. The weather only updates when the HU is connected to WiFi I believe. So connect it to your phones hotspot if you want to use that.

 

Yeah, I'mma reply to myself.

I had YTM do the "skip forward in the same track" rather than skip to the next track tonight. The only thing I notice I did differently was pause the track that was playing to make a few changes in the menu settings. When I resumed playing music, the steering wheel buttons would only skip forward a few seconds in the same track. I had to touch the track forward on the screen to skip tracks. It did not do this previously... I skip tracks a ton when I'm driving.

 

It’s like it was made for this truck. I am finally happy with the way my audio sounds. The EQ made all the difference in the world from the stock entune. Thanks to everyone who helped me out along the way. And thanks OP for doing this originally. Even though my wife didn’t like the price tag lol.

 

Got the correct radio antenna adapter and got that in today. Soldered the blue wire. Works like a charm. I've got to play with sound and levels, the radio is much louder than input from Android Auto.

Also, what does this grey cable plug into? I couldn't find anything it could connect to, yet in pictures above, I see someone has it plugged into something.

 

The grey wire is plugged into the SiriusXM antenna if you bought the tuner and want to have satellite radio. If no tuner then don’t worry about it.