The Florida Classifieds

I have some OEM rear leaf springs, as well as the rest of the OEM suspension, front bumper, grill surround , etc and rear bumper if you are returning back to stock. All from 1 owner, 2006 Tacoma Extended Cab TRD OR, with long bed in 1E7? Silver Mica at 70,000 miles.

Rear leaf springs were replaced under the TSB with the "Canadian" springs, which basically have an additional leaf.

Pm me to discuss possible trades or price.

 

Shooters World has some unknown to me brand for $29 a box. Talk about gouging!
I have about 4 boxes of Blazer Brass 124 grain stashed away but you are too far.
I rarely shoot factory ammo so wouldn't miss it.

 

Hi all I'm in Tampa and looking for a used 4wd Double Cab 5' bed automatic. No salvage titles or wrecks please, but I'm open to a lot of different build outs. This will be used as a daily driver and also on a hunting lease that is wet and soggy cattle pasture and horribly maintained roads that love sucking 2wd into tow outs. Don't want or need any tonneau/camper covers as I'll throw a truck box in the back and want open access to the bed. I don't have any particular numbers in mind on wheel/tire size and lift, but it would be nice to find something already up off the factory stock build. Heck I'll look at a 2010 as long as the mileage is lower(I drive a 2010 4runner with 84k miles) which is why I bring that up it's barely broken in. Thanks for your help.

 

I checked the rules and didn’t see anything against this so here goes.

I’ve got a custom built Glock 19 Gen 5 I’m looking to sell or trade for a Tacoma Gen 3 audio system. It’s a one of a kind piece as I did it myself. Nobody else has this design and I haven’t seen any Gen 5 Trump glocks at all, let alone in Gold.

Trigger has been polished and has zero sponginess. Also has Night Sights. Looking for $1475 OBO. Or trade for audio system for the truck or I can add guns for the right deal on a Harley.

 

Other than this place and craigslist, autotrader search engines are there any other sites you guys have had success finding what you need? I don't profess to be an internet wizard just want to cast my net deep and wide in my search and don't miss a great site. Thanks

 

I use offer up and pretty much find what I need i check it religiously

 

SOLD

3rd Gen Aluminum TRD skid
$200
Orlando

 

Also fits on a 2nd gen

 

Good to know. I can’t recall for sure but aren’t the 2nd gen and 4runner skids interchangeable?

 

Tbh idk, I think they are different size, but I've been wrong before

 

Very nice art work. I commend you for that!

Just curious about the finish. What was involved in the fabrication?

 

Did this sell? I'm in Orlando

 

Yes, I edited the post. Sold

 

Thank you very much! So it’s a four step process. First I completely disassemble and spray it down with special degreaser. Takes all the oils off of everything. The frame has to be sanded with a dremel to take off the factory stipple.

Once it’s prepped, the duracoat is easy. You spray three layers with ten minutes to dry for each. With the expensive metal flake stuff like this, you’ve got to do another three layers of clear on top with five minutes between each. You let it harden/cure for 24/48 hours and then reassemble.

the fun part is part three. I take a picture of the gun on its side (for both sides) I pull it into adobe illustrator and draw an outline around it. Pro tip: if you’ve never done it, I’d take the pictures before you dremel and use the OEM stipple as a guide.
Then I create a pattern that I think will work for the design. In this case there’s no pattern. Just a flag. I clip mask that and then I add the layers I want. I think this had like 4-5 layers. You’ve got the 45, the flag, Trump’s face, and the two outline layers. Then I make it all a single layer and pull it into my laser. There are lots of settings that matter here, but it’s too much to explain. Essentially I split some duplicate layers to get different depth. Okay with speed etc.

One I run the laser, I disassemble and clean all the soot off of everything. The reason I assemble in between is to A. Make sure it all fits together with the tolerance of the paint coat being added, and because it needs weight so it doesn’t move around on the laser since I don’t have anything built to hold it in place. Play dough works if I can’t keep it assembled or if it’s a small part.
After it’s disassembled I do the spray degreaser again on everything and clean it thoroughly. Before finally putting it back together I lubricate all of the parts with remoil and it’s done. It sounds like a long process tying it all out, but I’d say that most of the time is wait time. I thoroughly enjoy the actual process of doing it. Here is my EDC I did myself as well as some I did for friends.

 

Damn these look great

 

I’ve got a brand new in the box 16+ Pop and Lock for the tailgate.

Looking for $80 picked up. Located in the largo/Seminole area

 

Sold

 

Still for sale, $200

 

Not mine, but topper for 6' bed

 

I'll take it, how much shipped to 34479 and u do paypal