SCS BR6 wheels 16x8, 17x8.5, & 17x9

With our limited finishes like the blaze bronze lip, we only offer them a couple times a year.

 

Good to know they may come back. I’m in no hurry, fully satisfied with my SR8s for now. Appreciate your response!

 

anybody running 295 70 17 with these wheels/

 

Are you running any spacers up front with those wheels?

 

Getting mounted today

 

That run of brushed copper/black ring really got my gears turnin'. Like to see 'em make another appearance.

 

How do we go about ordering the beadlock conversion when ordering? Will they also powdercoat/machine the lip prior to installing?

 

16x8 -12mm on 265/75 KO2s on stock suspension. The rear looks like it's sagging a little but according to the tape measure its actually still about 3/4" higher when the bed doesn't have four wheels and some other heavy stuff in it (like it does when I took this pic). My next tire will likely be a 285/70 but the dealer had these tires on special for buy 3 get one free so you know I couldn't pass that up.

 

Do you also have OEM UCAs? I’m looking at these wheels and wrapping them with ST Maxx 255/80 and have been reading to see if they are going to rub. So far it seems that they won’t or at least most 255s don't or only have minor trimming. My trucks lifted about 3”. Want to hold off on UCAs for a bit if I can.

 

255s or even 285s will never rub on the UCA. However, adding UCA can help gain more positive caster which will help minimize rubbing in other areas such as the cab mount area.

 

Thanks for the info @SCSPerformance, good to know. Worried about that cmc too but with the -10 offset and 4.3 bs I don’t think that’ll be an issue. My original concern came from looking at the JBA site with what wheel/tire sizes work.

Thanks again for the insight now I’ll patiently wait until there is a restock of those 17X8.5 Matte Dark Bronze wheels. The BR6s are some great looking wheels.

 

You can subscribe to our New Inventory subscription thread if you haven't already. We will make a post/announcement 1 or 2 days ahead to let everyone know when our website will be updated with new inventory. They will be sold on there on a first come first serve basis.

 

I’m keeping an eye on there, your FB and Instagram pages as well. Also SUV’s to the blem page as well, just in case. Thanks again for the suggestion and extra information!

 

The 255s have lots of room, with these wheels, between the tire and the UCA. I have no rubbing of any sort with my set up. You will only need new UCA if you are wanting additional caster.

 

Thanks for the info. I’ll have to see what happens after wheels and tires. Alignment right now looks and feels ok after I got it done post lift.

 

295/70

 

I got the answer to my question, in case anyone is interested. The 3/4" Bora wheel spacers fit without a single problem. You can see from the pics that there are gaps in the wheels for the original studs to fit in to. I bet a 1" set would cover the original studs completely because there was less than 1/4" of stud poking out beyond the spacer.

 

2 of my 4 br6 16x8 -12 offset br6 have arrived

super pumped to get them mounted next week. Cmc in October too!

 

Great looking wheels! What are you wrapping those in?

 

For now some cheaper trail tires — Thunderer Trac grip MT 285 75 16 They look super dope and I like the way they ride so far. Slight rub on control arms from +25mm offset on stock rims. This will fix that and cmc I’m Doing in October will fix any rub behind front wheels. Also strike bumper will give me loads of clearance up front.

So the tires will swap from this: