Colorado Trading Post

Zipties.

 

Water tanks are sold to Coop,

who needs a gas can with the spout and cap?

 

fs: Bilstein 4600 kit for 2nd gen Taco
5k miles on them

front and rear

asking $300

pm if interested

 

I have a k&n oiled filter for 3rd generation tacomas, replaces your factory filter. Used for maybe 6k miles. $20 and it's yours!

I also have a stock double cab 5ft bed exhaust I'm trying to get rid of, $30 obo!

 

WTB 5" of 3.5" exhaust tube

 

I’ll go for the gas can with spout and cap. PM sent.

 

Not sure when mine got the W shaped droop, but I noticed it about 8 months after install. No heavy hauling or towing in that time. I've been working with the retailer/installer on a solution for a few weeks.

 

FOR SALE

MBRP T5073 Exhaust Tip, 6" O.D. Angled Rolled End 4" inlet 12" length (BRAND NEW)

$50 obo


https://mbrpexhauststore.com/t5073-...qXWSNZlt10sDx0FsGHAhwqnCprpXNNRxoCrfIQAvD_BwE

 

@literallynothing go chrome or go home

 

I was already thinking I need to measure my exhaust and see if it’s the right size

 

You need to go home

 

Anyone want a brand new steel winch cable and roller fairlead for Free.99?

@JasonLee Should be able to bring it down to the front range this weekend.

 

I know this is a bit dated, but I have one in Sliver, with the tow package if you still need one.

 

I have one for a 2009 if you still need one. I also have the 40% side. PM me if interested. I'm in the Springs.

 

Got some Fall cleaning happening in the garage. Wife says I need to make room. I would prefer local pickup in Colorado Springs, but I would be willing to meetup or use the TacomaWorld Express. PM me for any more details. PayPal or cash preferred.... I have the following:

Scan Gauge II- Used, but in good condition- $100.00 OBO ***SOLD***

AEM X-Series (52mm) gauges. Both are basically new, I installed them for one week, decided to go in a different direction. Both gauges complete with the wiring and sensors. AFR gauge-$150.00 Boost gauge- $225.00, both for $325.00

K&N Cold Air Intake for 2nd Gen (2009)- Used but in decent condition. They are currently out of stock, not sure if you can get these anymore. - $150.00 OBO

LoTech A-pillar 2 gauge pod for 2nd Gen, Gray. Brand new still in plastic.- $50.00

Expedition Essentials Bedside Compartment air compressor mount kit w/ manifold mount and ARB twin compressor extended wire harness- Brand new, never used. Fits both 2nd and Turd Gen.
Mount- $125.00
ARB extended harness- $120.00
Both- $230.00

Undercover Swing Case- Used but in decent condition. Definitely fits 2nd Gen, should also fit 3rd Gen- $100.00 OBO

Apex Mid cab bed cage for 2nd Gen short bed. Welded and powder coated (touched up w/ rattle can). I've added the mounting plates, quick fists and 'tree' sliders on the sides. May fit 3rd Gen as well- $450.00 OBO

2009 chrome bumper w/ tow package, basically new condition w/ little dimple on lower right.- $100.00, trade or OBO

2009 rear seat cubby storage, used. Free

OEM 2009 A-pillar, gray. Free

 

Interested! What version, aka how old? Would you ship USPS Priority Mail if I send you a label?

 

Sold...

 

Not sure of the version but I got it in 2016, and used it until last year when I upgraded my head unit and monitor all that stuff through it. And yes I would be willing to ship it to you.

 

Ok 70$ obo or trade for?

 

Getting my 2011 DCSB ready for a Snugtop Sport Hi-liner install in a couple weeks up here in Vail, CO. Realized my original non-TSB 2 leaf spring pack is totally sagged (photo below) ... ISO and looking all over for a good condition , low -mileage 2nd or 3rd gen TRDOR take-off suspension... Mainly want it for the leaf pack but will certainly buy the springs/struts as well. Please let me know if anyone is selling one... Seen a few in Denver but had high miles and high cost...

Also - would anyone know of the best mechanic/shop up in the mountains that would install a used 3rd gen take-off suspension onto a 2011 DCSB? Or any TW'ers want to help out? I feel like I could do it but don't have a garage or a floor jack/stand etc. Thanks for any insight! Trying to get it done before winter.

You can see my rear end is sagging quite a bit: