OBA -> On Board Air Mega Thread & BS

Can anyone recommend a surface mount quick connect for my ARB compressor?
Preferable cheaper than the ARB model and with some kind of cover/plug to keep sand/water out of it.

 

I just used a NPT quick disconnect female air fitting on my bumper (https://www.homedepot.com/p/Husky-3...ck-Connector-Kit-5-Piece-HDA71900AV/205190585) and use a rubber chair tip (don't recall the correct size but basically this: https://www.homedepot.com/p/Shepherd-1-in-Black-Rubber-Leg-Tips-4-per-Pack-89128/100138443). been using it for years though I have changed out the female fitting once or twice in that time frame.

 

here’s what I have

http://absolute-wits-end.com/air-coupler-bracket-angled-kit/

+

http://absolute-wits-end.com/quick-connect-air-coupler-pacifier/

 

My solution:


Including protective cover from Home Depot

 

Here’s what I have on my bumper

Eaton Weatherhead 1873X4X4 Brass...

$36 Eaton Weatherhead 1873X4X4 Brass CA360 D.O.T. Air Brake Tube Fitting, Female Bulkhead Union, 1/4" NPT Female x 1/4" Tube OD

https://www.amazon.com/dp/B00BKF979O?ref=ppx_pop_mob_ap_share

 

Got my ARB installed today using the Rago mount. Always shocked when things work on the first try.

 

With the addition of an aluminum plate the Slee Offroad bracket for the ARB compressor can be used to mount a Viair compressor in the engine bay. This is on a 2014 TRD Offroad.

a little more detail in:
https://www.tacomaworld.com/threads...en-tacoma-today.6499/page-10489#post-23985946

 

Does anyone have pictures of how they mounted a quick disconnect/air chuck on a 3rd gen behind the grill but in front of the radiator?

I have my compressor mounted next to the windshield fluid reservoir and i already have the stainless leader hose but need ideas on how to mount the chuck.

Ive searched but could find anything andy eyes are cross eyed from going through this thread.

 

wits end quick connect kit

 

you can mount a frame nipple on a simple homemade bracket from angle aluminum. The frame nipple has 1/4” NPT threads on the inside with a threaded outside and comes with a nut.

KOOTNAS 2-Pack Solid Brass Bulkhead Fittings, 1/4 NPT Taper Female 3/4" Straight Male Thread Brass Connector with Metal Wave Ring, 1-1/2" Length Brass Coupling Fitting

https://www.amazon.com/KOOTANS-Female-Fitting-Bulkhead-Nipple/dp/B07PBF6CLK

 

tonight I found some interesting stuff..

ADS system
https://updownair.com/product/toyota-tacoma-gen2-ads-system/

Rago Fab "wifey" air system

 

I just got my up down air system today in the mail. I’m gonna have to figure out a place to put it. My power tray is taking up the room in the place where their bracket goes. I’m going to have to make a bracket and get it over in that area in the blue circle. I kinda makes more sense to me to keep it over by the compressor anyways. It also didn’t come with instructions on installing it. It said to look at their website for instructions..... nothing for a Tacoma. Probably gonna have to follow the Wifey instal You Tube video. I’ll have time next week to mess with it.

 

Where you have circled is where my compressor is. I have a 2010, so I dont have anything there. I just mounted my compressor using a piece of 16 gauge steel that i bent, but its rusting through now. Ive been looking for another suitable mount, but haven't found anything yet.

I did find some stuff on Rago Fabs site, but its for the other side. Thats where I have my sPod mounted. I also dont want to move the compressor to where you have it, because Id have to get a longer air line to go back to my tank (not a huge expense, but i want to use that space for something).

 

I'm just imagining one of those as seen on TV commercials where the lady goes for a Tupperware lid and the piles of Tupperware spontaneously go flying all over the kitchen...
Pulling out a hose isn't that difficult, 10mins of talking shit while you walk around the truck isn't that bad. Also it's way cheaper to make your own daisy chain if you really can't be bothered to air up 4 whole tires seperately.

 

I'm of the same mindset. Never been sold on the multi-chuck hoses, but maybe if I tried one I'd change my mind

 

Hmm you might be onto something.. I need to start a youtube channel and sellout to anyone that is willing to give me free products to hok.

 

I think those systems have hard lines that are mounted near each wheel. But i get it. I am not going to get one. Thought it was an interesting idea

 

Made some progress tonight. I chopped the bracket down, added a hole and bent it to fit the Slee Mount.

 

i may eventually do this down the road if i decide to upgrade to a dual arb. Would be nice to air up the same pressures simultaneously but with short 2-3ft sections or air line. I like the sponsoredbywifey air system but I’d likely just make it myself.

 

Those systems seem cool. Just not sure how it saves any time? Spend money and time on install, but I still have to get the little hoses out and walk all the way around my truck....twice.