What have you done to your Tacoma today? 1st Gen Edition

Finally got some new bolts and threw on my old burnt exhaust tip from the last truck I had

 

Got my truck aligned today, it’s riding great. Cleaned up the skid plates a little and gave them a coat of flat black, going to put them on later and retorque all the suspension bolts.

 

Anyone ever make a custom cold air intake. Yes I know the stoc is better but it will no longer fit. Tube needs to be short to clear the shock tower. And what does the rubber tube by the top do?

pfa

 

What are fender liners?

 

Those things that keep the stock air intake from taking in water

Snorkelers need not worry

 

@ROlla-Xrs got mine in the mail today, appreciate the fast shipping and quality product

 

Stuck my controller up in the headliner. Got a lot of wiring to do now.The control module is getting stuck in the rear cubby.

This is a Federal Signal siren and light controller out of a cop car, but I flashed it to a wrecker/towtruck spec. Disabled all the siren tones. I’ve got five switches on the bottom row dedicated to accessories.

It has a lot of cool features like a PA system and radio rebroadcast, I have it set up to have an aux jack so I can play music out of the siren speaker.

 

Enjoy

 

Got mine too... @ROlla-Xrs

Good stuff

 

Installed @Tttacodan bed supports today. Followed @chowwwww and installed em backwards to the 2nd gen instructions. The rear of the bed bevels and the supports fits more flush this way.
Now I just need to grab more hardware to fill the missing holes.
The tailgate finally closes.
I’m extremely happy with the product and end result.

Sorry for the crap photos it was late, and they uploaded sideways?

 

I want those

 

I drove an hour to pick up a $25 toolbox for my truck. One of the top corners was smashed in so I did the hot water trick and rounded a dowel and cut a flap on the inside plastic to access it. Pushed it out and then JB welded the flap back in place. You never know I was in there. Then I went to Home Depot and got all new weatherstripping and Ace Hardware for J hooks. Drilled the bedliner and installed. Fits perfectly. Needs keys so I may have a locksmith rekey but it only holds my tie downs, ratchet straps and jumper cables. Nothing that important or expensive.

 

Anybody else with the 03-04 throttle bodies having random lack of throttle?

 

https://www.tacomaworld.com/threads/throttle-body.700410/#post-24849438

 

I had just put the cap on and the damn tailgate stopped wanting to shut without having to pull the latch first. You could also see the large gaps from my bed sides pushing away.
Stumbled upon these, snagged a set. Came fast, super easy to install, and work excellently. As the bolts were tightened I got kind of giddy because you can feel the bed side being pulled much more true, Haha

 

Thanks. I have to get a multimeter to check but I’m not sure if it’s any of this.

I’m not getting any codes and while I’m getting this issue the throttle is still there. I just have to move the accelerator further to get the same amount of throttle. I’m fairly confident that it isn’t limp mode.

The issue is much more prominent in the summer when it’s hot. If I turn the key on and depress the pedal a few times before I the turn the engine on the accelerator is much more sensitive and feels much better. Over a short period of time it sort of drops off and feels a little lazy.

I’ve had this throttle body and the sensors brand new from Toyota for a year. The factory one did the same thing but with other symptoms at idle.

 

Installed 33'' KM2's.. runs like a hog though lol

 

Looks good

 

sell me your old transfer case mount

 

Blew an axle seal today that I found after going through anza borrego. And it's making a clunking noise, hopefully I didn't bend the axle or something. Doesn't sound like the drum rubbing, more of a rhythmic clunking sound.