Stealth Custom Series F5 * Photo thread *

I have my F5 on the way! After a bit of looking the 6 bolt selection with 4.5" backspace is going to be as close as close to stock in this rim.

I believe the stock backspace is 4.9" so not much difference there. I have 265 70 16" on my 2015 SR5 4X4 and only noticed a bit of rubbing on the front mud flaps after installing some 1" wheel spacers.

I believe my 16" stock rims have a slight + offset.

If you aren't putting on wheel spacers (to give the truck a wider stance appearance) and stick with the above tire size you should be okay in terms of rubbing.

Hope that helps?

 

For sure, Thank you!

 

Finally got them mounted!



Before and After (ignore the wood ramps):

 

Looking to get some F5’s just not sure about the sizing/BS was thinking about 17” 8.5 but see a lot of folks running 16” in various BS options just wanting to know why you would choose a 16” over 17” and Vice verse. My tacoma is a 2018 off-road I am going to be installing a toytech boss 2.5 plus OME add a leaf with SPC upper control arms. I fully plan on doing some chopping to avoid rub not sure about CMC or relocate will cross that bridge when I get there if needed. Also planning on 285/75/17 tires or equal in a 16”. Any advice would be appreciated also a side view picture of a cement tacoma with black F5’s 17” 8.5

 

Got my wheels! I went 16" because I like the look of more rubber without having to CMC as I'm going with a 265 75 16 (only one size up) but I went -25 offset so we will see. What I have to do. Install on Tuesday!!

 

​

​

Heck yes ​

 

I love these wheels

 

waiting on that restock for 16x8 -25!!!

 

waiting on 17X9's myself.....

 

I have only slightly modified my vehicle height. Just went with a set of 5100's to level the truck out. I would like to get a set of 16" bronze f5s, but I see that they are sold out. I am a bit concerned about the tires rubbing. I like the Stealth6 too. 16x8 -25mm 6x139.7. Would that work with a set of 245/75/16s without needing to cut/have any adapters?
Thanks

 

SOS!! Can you peeps that have 16x8 -25 offset post a pic of your CMCs! Im going to run GEOLANDERS MT 285/75/16. I am getting a CMC done tomorrow and I need some reference to go off of on trimming the plastics. I have a 2.5 lift rn as well Thanks in advance!

 

Cut it as far back as possible and don’t let the bushings catch fire. This is all I could get for you right now

 

Finally got my wheels mounted!

If interested set up:

265 75 16 duratrac
2020 TRD pro front shocks with RC leveling kit
Rear two inch lift block (stock shocks stretched to the max and getting beat to hell but I like the look and am broke lol)
Shaved badges
Powder coated stock running boards and.left plastic steps off

 

Niiiiiiiice ​

 

This looks fantastic! Any rubbing to report?

 

Removed both mud flaps and haven't had an issue since! Minus the rock flingin

Edit: thank you!

 

Awesome, thanks for the feedback! I've got the -25 wheels here already and I'm waiting for the rest of my suspension refresh goodies before I buy a set of 265/75R16s.

 

Sweet liKe that colour wheel! what colour is your truck?

I would recommend removing those mini front mud flaps before installation I ended up ripping a bit of the well liner out when I was reversing at about half lock on my way back from the shop. You may be able to get away with leaving the bigger set on and mitigate some paint damage due to rock slinging

 

The truck is Silver Streak Mica - got the silver spoke stickers to tie in with the truck. The sides of the truck are all scratched up from trail pinstripes, so the rock chips will blend right in