Official* New England Buy/Sell Tacoma Marketplace

Nah sorry - I think those won't work for a Gen 3. First, I don't have a front rail but those are easy to get, if I did get them I am not sure that the front rail and side rails are the same level on the gen 3. Could be wrong, but I don't have a use for those could do a CB antenna there but I might get a trifold and the brake light bracket works for that.

 

Interested in the corner brackets and the t-nuts.

Also a question about the window visors. Are they in channel and what brand? And are they considered low profile?

Prices?

Thanks!

 

The vent visors are in channel weathertech units. I would say they are low profile, as the stick on ones are typically much more bulbous... Pm sent.

 

Much easier to source t-nuts. Just rip the plastic off of them. There is also a spring version that you just take the spring off.


https://www.homedepot.com/p/Superst...t-Gold-Galvanized-5-Pack-ZCM100-3-8/100189687


https://www.homedepot.com/p/Superst...nel-Spring-Nut-5-Pack-ZA1003-8EG-10/100179881

 

I also found that using an angle grinder to flatten 2 sides of a carriage bolt work great in the t slots as well.

 

ALL *SOLD*. Thanks!

Sold a bunch of stuff to Yota, Ace, & Rusty! Thanks doods!

 

Looking for gen 3 tri fold rigid tonneau, not a soft one. 5ft bed. Price limit 250. Seen a few on Facebook but wondering if anyone on here has one. Could stretch to 300 potentially.

 

New Fender Mustang LT25 Combo Amp. $150.00 it costed me a little bit ago and played through once $80.00 local


https://www.sweetwater.com/store/detail/MustLT25--fender-mustang-lt-25-25-watt-1x8-inch-combo

 

Tentative here, but here goes:

WTT - (4) OEM FJ Steel Wheels + Replica (?) Center Caps + Lug Nuts for 2016-2019 OEM Sport Wheels

I bought a set of brand new OEM Toyota FJ steel wheels the summer of 2019 and painted them silver. I bought a set of correct center caps from Ebay, but I cannot attest to them being OEM, my guess is they're repops, but they work fine with the OEM FJ steel wheels. I've run them on the truck for only the past winter. I just find I don't love them as much as I had hoped I would, so I'm thinking about changing it up for a set of 2016-2019 Sport wheels.

I'd like to do a straight across trade with us meeting at my local tire shop that does great work and just swap them over. I have steel wheel lug nuts, but without a thin wall socket, they're a bit tough to get off. I do not have TPMS on these wheels, but I don't believe the TPMS from the Sport works with these without some finagling. If you don't want to keep your TPMS sensors I'd love to keep them, but that's your decision.

My wheels are effectively perfect outside of a clearcoat run or two and one place where some dirt got into the finish. I'd like your wheels to be basically mint with no curbage, scratches, dents, bends, etc. Obviously I'd like close up photos before we'd meet to make sure we're both in agreement on condition, etc.

Photos were taken this afternoon (2/28). I'm not interested in selling outright as I won't have any wheels to roll on for the winter. I've been actively looking for Sport wheels but haven't found anything in my rough budget in the condition I'd like.

I'm located about 30 miles southeast of Boston.

IMG_8706 by Mike M, on Flickr
IMG_8705 by Mike M, on Flickr
IMG_8704 by Mike M, on Flickr
IMG_8703 by Mike M, on Flickr

and how they look on the truck.
IMG_2931 by Mike M, on Flickr

 

Selling my Accessory Skid Plate.

https://www.tacomaworld.com/threads/fs-2011-trd-o-r-accessory-skid-plate.710109/#post-25241052

 

ISO a nice aftermarket rear bumper. Figured I would ask if anybody is selling one, not really sold on a particular design yet.

 

Hey anyone knows of or selling a Kayak for cheap?

 

Hey Jeff

How cheap are we talking?

 

I don't know, I'm just starting to look.
If you have ANY recommendations or hints they would be greatly appreciated!
Pricing? I was thinking 150 but could flex from there.
I've never owned one so I do not know what is good or not good.
It's like comparing a Toyota to a Nissan.
I have a canoe but that is not working for me now.

 

I don't but is your OEM in good shape and what colour

 

Chris.....are you looking for one?

 

I have a rear sub bumper if you want it.

 

Not in the best of conditions but id give it a 5.5/10.... the main problem is a dent on the passenger side that could be hammered out (not sure if it will go back perfectly but can still be made better). It's barcelona red. I can snap some pics of it if you want but I wouldn't let go of it until i have my new bumper in hand.

 

Not urgent but wouldn't mind, mine got hit last year and one side is bent a bit.

Any pics?

Hoping to get one I don't need to hammer, but I'll keep in mind

 

Its 3rd gen I just realized you are running 2and gen.