What Have You Done To Your 3rd Gen Today?

No problem, let me know if you have any other questions! It's a lot to take in at once but it's not terrible. It just depends on what you want to do with the truck -- if all you want is to match front and rear ride height you can probably be fine with spacers, just be aware that it's a compromise in terms of ride quality. If you want to match front and rear ride height AND have an equal/better ride quality, you should look into replacing the shocks and springs (at least in the front).

It all depends on what you're looking for!

 

that is all i want to do is match the front and rear ride height.

so if i went the spacer route it wouldn't adversely affect anything? and would i go with a 1" spacer or what?

 

I would suggest looking at the RoadMaster Active Suspension kit. It is a DIY install and adjustable if your cargo requirements change.
https://activesuspension.com/

 

thanks, i will check it out...

 

I highly recommend that you give headstrong a call. They are more than happy to fully explain each system with advantages/disadvantages. From what you’ve said, my recommendation would be to go with the Bilstein 5100s up front with the stock springs. Several people on here running that setup. The 5100 has an adjustable spring perch that will work similar to a spacer, but without screwing up the geometry of the suspension. I’m running these shocks, but I have them set to the lowest setting and used stronger springs (OEM 8888s) to lift the front end. The 5100s will give you more options down the road if you decide to do a true off road setup as well.

 

Might be the lighting, but, colors seem to match pretty well!

 

thank you! i will be contacting headstrong

 

$29 ESI Ultimate Tailgate Seal with Taper Seal 10ft for use with Truck Caps and Tonneau Covers

Tailgate seal on bottom of cab doors with holes knotched out for the window drains/weep holes Thanks for the idea @Trim taco

Sorry for the crappy pics. This should cut down on some of the road noise (I'll test tomorrow)

 

I just peeled mine off.

 

How did you “bend” them closer together? And, did you simply bolt the angle iron to the flange on the stiffener? Thx

 

Ah, never mind as Rosanadana would say. I just noticed the shiny new bolts on the outer flange.

 

Rosandana, you’re showing your age... good times!

 

Yep. And that was pretty much the last times SNL was actually funny!

 

Got the upTop Overland scenePOD 2.0's + the Baja Designs rock lights installed on the Bravo roof rack. 400 lumens of goodness right there!

 

Meeeeee toooooo.

 

Quick sneak peek of the light whip. Fun little project, although, not quite buttoned up.






Using one of these tabs, this fold-down mount and

AddSafety 5FT RF Remote Control RGB LED Whips Light with Spring Bases Dancing/Chasing Lights (5FT-ONE, Remote)

this whip.

Currently, powered by an

Biswaye 2-Pack 12V Replacement Lithium Battery 2500mAh (Closed)

M12

$20 【Multifunction 】 12V USB Power Source Replacement for M12 Milwaukee 12V Battery Charger M12 Adapter Compatible with Milwaukee Heated Jacket 45-59-1201 USB Charger

power source with

OdiySurveil(TM) 5Pairs 2.1mm x 5.5mm Female Male DC Power Plug Terminal Adapter for CCTV Cameras

adaptor, but will eventually be hard-wired in with something like a SAE plug. I'll eventually get a rubber rod holders like these to secure it in place when not in use.

I'll take better pics when it's all finished up...

 

It wasn't too difficult, you just have to take your time. watch a few videos on how to apply vinyl using a wet method.

 

Got the transfer skid installed

 

Looks nice, but that's too flashy for me!

Currently, I have a DIY Olympic Platform with Rogue RM-3 Monster Rack 2.0, Adjustable Bench 2.0, Weight Tree, Boneyard Ohio Bar + 260lbs MIL Spec Echo Bumpers & Random Dumbbells. Planning to eventually get a cable machine with a leg extension/curl attachment, either a full dumbbell set or and adjustable dumbbells, and calibrated kg plates.

 

How did you eliminate it, just ran a new line or ?