What Have You Done To Your 3rd Gen Today?

This past week I've been busy with the truck. I purchased and installed a black HPS Silicone Air Intake Hose, AVS low profile ventshades in dark smoke (to match my bug deflector I put on a while back), demon brackets with Grey shackles, Toyota tailgate lock (PK3B6-35JSO), desert does it seat jackers on my passenger seat for the boyfriend, ECT always on mod from ebay along with a MESO extended fuse cover, and a Tyger soft roll up tonneau cover.
Finally today, gave it a much needed wash, clay bar, polish, and wax after our camping trip this past weekend. Tomorrow, I'll move forward to detailing the interior.

 

Nicely Done! Are the bed side rails still usable with that tonneau cover? Like if you wanted to leave the bed cleats in?

 

I installed one today and yes they are still usable (on most tonneau covers)

 

C&C?

 

Couple weeks ago when camping. Not much a mod, just playing around.

 

those headlights are sexy

 

Yes, they are usable, which was one of the reasons I chose this one. Also because it was cheaper and the sun kills black trim in AZ. The install took maybe 15-30mins. Not terrible at all. Only required a screw driver and 10mm

 

They were expensive but I’m really happy with the purchase.

 

New seat covers. No more cloth

 

What brand did you go with?

 

yeah they are expensive af. I've been thinking about getting a set since September 2020 lol. Might hold off until the summer because I'm going to install a roof rack and rock sliders next

 

Prestige

https://www.prestigeoffroads.com/

 

What I have setup so far (working progress as I find what I need or think might need)

I wanted a breaker bar but also wanted 3/8 drive so it was I think 10 or 12” which won’t be enough leverage in some cases so I cut a hollow tube for a cheater. Drilled a hole to keep the breaker from sliding out with a hitch pin. Strapped with the tire iron bag. The little pouch from blue mountain fits perfectly on the other side of the jack- only have a 21 and 19mm deep for the lugs and spacers, 1/2” for the replacement Colby tire valve kit. Led safety flashers for side of the road- fit perfectly in the spot above the jack.


Behind the seat I have a torque wrench (mainly for the lugs), blackjack tire kit (Colby tire valves inside), noco40 charger and cables. The battery cables might be removed completely or just transferred to the box in the bed. Not sure if I really need them for a backup to my backup. But everything fits in snugly into place

 

Thanks! I was leaning towards the rough country one, but I think the roll up feature will suite my needs better than the tri-fold types. This one appears slightly cheaper too, which is a bonus. Hopefully this summer in AZ won't be the record breaking heat wave that it was last year.

Edit: I see this is a tri-fold too.

 

I hear you. I bought them drunk and impulsively. I got the Cali raised sliders because they were affordable and so far they’re awesome. I haven’t come down on them yet but use them to Jack my truck up when needed.

 

Those looks awesome. Can’t find them on their site though.

 

New shoes!

 

Hahah thank you. It's getting warm already, I hope it levels out soon and doesn't keep climbing. The specific one I got is a roll up (I needed a roll up because we have an in bed tent for camping) try this link.

$206 Tyger Auto T1 Soft Roll-up Truck Bed Tonneau Cover Compatible with 2016-2023 Toyota Tacoma | 5' (60") Bed | TG-BC1T9044

https://www.amazon.com/dp/B01M0L5IVL?ref=ppx_pop_mob_ap_share

 

Nice looking truck. It's got that industrial/commercial vibe going on that I like.

 

Had the windshield replaced