What Have You Done To Your 2nd Gen Tacoma Today?

Nothing major here....spent 5 minutes removing the white meso st wheel ornament and replacing it with cement which goes much better with black and gray interior.......

 

Also took large 2gb thumb drive and used tiny 8gb micro sd one in it's place for more music and more inconspicuous when in port on dash.....

 

Took her to the beach.


Saw this Ford stuck so I hooked up to it, locked diff and ended up burying myself. Winched off of a buddy to finish the job.

 

Drain and Fill Transmission Fluid.

Its about 75% Valvoline MaxLife, 25% WS

 

Her first wash of 2021.

 

I liked their design and being all stainless and aluminum I knew they would last, they had many many attachment points so I didn't have to stack ring terminals off the same lugs as I had them I was tired of cheap terminals craping out on me (stretching, breaking, rusting, deformation) after only a few on/off cycles due to crap materials. I could maintain my factory cable terminals without further modification. Lastly I was already ordering some other stuff from SDHQ and said screw it they a little expensive but they are high quality well thought out purpose built product and I need terminals so add to cart.

 

Well, I got a little over half of the work done this weekend. Rear lift, shocks trimmed all the fenders up and picked up the tires. I’ll get to finish the front after my work trip. It’s gonna be a long 2 weeks waiting to get home

 

Nice thing to do but I love rolling by stuck full sizes on the beach with the look on my face like " there is literally nothing I can do for you other than look good rolling by you"

 

Your truck looks awesome btw. Good job on the fenders

 

Good looking truck, you should hit up the Wilmington forum if your havent already. Im local as well

 

It is pretty funny but then I figured it would be funnier to be pulling a full size out as well. Made a circle around him first cruising through the deep sand he was stuck in before pulling in front lol He was pretty mind blown by it and saved him a tow bill.

I really appreciate it man. Took a while getting those bolts countersunk in but so worth it to never have to worry about them again.

 

I just did mine so I know the process. I didnt bolt them down but did use new clips. I ended up making new supports for the rear as the bedsides were flapping. Little things like the fenders may not seem any different to the average joe but to other tacoma owners they look and say why does that truck looks awesome?

 

I dont drive my wife's Subaru often. Last week I took it out and it was painfully obvious from the violent vibration while braking my wife has been keeping secrets. That being said, today I replaced pads and rotors on all 4 corners. Still had enough time to chop up my spare grill insert and installed my Custom Car Grill insert into the surround. Gotta roll without a grill tomorrow while I wait for the glue to set up.

 

Did this earlier this week. Repainted my front bumper. It needed this badly didnt take before pictures but here's the done product

 

I reused/ repositioned the old supports for fenders and will be reinforcing the rears as well

 

I fully agree. I love of them looked trimmed regardless of having to do it for the tires. Just gives the body a much more aggressive look. I actually left a tab behind from the original bedside and tied it into my bumper and it’s more solid then it was stock. Your truck looks so good as well man.

 

I’ve used these several times. They don’t come out perfect, but mostly makes them disappear. Plus no running cracks!
Very easy to use. Need about 30 minutes and some sunshine to cure it.

 

Goodbye chrome bumper.

 

Sunset glam shots on my way home from work sorrynotsorry. Purple mountains - clear skies - beautiful az sunsets - & MY FRIGGIN TRUCK

 

We ain't twinnin anymore brother finally got my front bumper finished today (obviously need a couple LITTLE things)

Camera was dirty on the last pic