What Have You Done To Your 3rd Gen Today?

Took off the TRD 4x4 decals from the bed

 

For sure

 

RC 6 inch with 33x12.5x18

 

Putting a 6 inch lift on a new truck require more butchering than a cab mount chop.

 

This is better

 

thats a nice looking truck

 

Iron x smells nasty

 

Got a KDMAX 6.0 tune by @SubaruTheTacoma yesterday. First Rate . Truck Rips and if your undecided , just do it. Probably didn't need this little OBD cover. But heck. https://www.ebay.com/itm/DO-NOT-FLA...-PLUG-3D-Printed-Tune-Saver-mod-/114018497154

 

Props, looks great. I know most don't wanna part with the badges when they pay for a TRD but it does look so much better in my humble opinion.

 

For whatever reason I took the decals off my f150 platinum Aka the fx4 ones but don’t mind the Tacoma ones

 

Ok, it looks awesome lol.

 

Installed bed lights today. Make sure the switch for the cargo lights is in the off position or disconnect the negative battery cable. Remove the taillights. Remove these two bolts (10mm)........

Pull factory harness away from body and remove the dust cap....



Plug the harness provided with the kit to the factory harness.......

Remove the plastic cap from the light cut out......


Run the kit harness through this hole in the taillight cavity to the cut out in the bed......

Connect the kit harness to the light and test.....


Hook the top in at an angle first then press the bottom in until it snaps in place......

Next......



Make sure to order this part number for the kit (two lights and harnesses). This part number with a -AA extension is the light only. ......

Don’t forget to reinstall the taillights.

 

Damn, I like that a lot.

 

Thanks I guess I will give it a shot. The iron fallout looks awful to me but I guess most don’t notice it.

 

Doctors need to write on the limb they're amputating so they remove the correct one...

Got an oil change and specified three times "don't touch my air filter or fill the washer fluid" yet the reservoir was filled with their cheap crap at the end.

You are DEFINITELY justified purchasing that cover, and even still it may end up flashed.

 

My Dealer will never find my port if they can't see it. Got a Blue one. That will confound them even more. Lol

 

Is that the Leitner rack? From what I have seen the best engineered rack on the market. I will probably get one. How was the install? Painful or doable for a rank amateur?

 

Taking the dam off tomorrow!

No rubbing with tires at all and the suspension is still stock. Any bigger and I'm sure there would be a bit

 

Yeah man, that air dam gives such a dorky grandpa look to the truck.

Speaking of... I've got a free air dam for any dorky grandpas in the Portland area.

 

I finally got the BAK Revolver Tonneau that I've been wanting forever. I like the fact that it can be used even with a bed rack and an RTT (maybe some day). I actually got the X4S which I like even better being all black. I picked it up through a recent TW Group Buy. Now I finally feel like I can leave my Axe, Shovel, and Fire Extinguisher in the bed rather then pulling them out for my daily commute. Unfortunately, when rolled up, I could no longer hook bicycle forks to the mounts I put on the head rail (like @[TACOMA] posted here). I thought about moving the bike mounts from the front rail to a set of VooDoo crossbars I use to transport skis. The only problem there was that the Tonneau moves the bed rails just a little closer together. Luckily, I was able to find a couple "J" hooks and (other than the fact that I can't close the tailgate with the bikes on board) I think I'm in a pretty good place I think I might need to look into a ROK Block Tailgate seal though since I need to leave the tailgate down to transport bikes and skis now.