What have you done to your Tacoma today? 1st Gen Edition

Not locked
https://youtube.com/shorts/LJLOJWeM6LU
?feature=share


Locked
https://youtube.com/shorts/1xZsJhEglRc?feature=share

 

Looks like the diff mount arms are moving in the bushings. I am sure it is worse looking because the wheels are not on the ground.

edit: Also looks like the axles are binding on rotation. Also caused by the droop from being up in the air.

 

That's your CV binding. Are those aftermarket CVs?

 

Just that side is after market

 

That's 100% your problem. Throw it in the shit can and replace with an oem cv.

 

I have one in the garage, I’ll swap it out tomorrow!

 

OK, so in trying to make sure I'm ready to go for all my bushing installs, I'm looking at the Strongflex LCA bushings and wondering if I need to go source some large washers.

What's in the Strongflex "box":





What's in the Whiteline "box." (note the 8 washers) As I recall, these go on either side of the bushing, against the frame, to prevent the bushing from rubbing on the frame.



Is this just a design difference from manufacturers, or an oversight from Strongflex?

@Blackdawg

 

no washer. Goes right in the LCA mounts. Just like my Solo arms and MCM arms.

LongTravel Install-13.jpg by Monte Nickles Photos, on Flickr

SoloLCAandCamGussets-46.jpg by Monte Nickles Photos, on Flickr

 

Thanks. Why the difference? Just a difference in the poly hardness compared to the rubber or something? (just trying to learn)

 

pretty much yes. Think about your leaf springs. No washers there either. The idea is that technically you don't want the bushing turning in the arm. You want the arm to pivot off the bolt inside the sleeve. So if the bushing is being squeezed between the mounts it's less likely to turn. You also don't want the arm to pivot with the bushings as the pivot.


Now...that's idea. But also noisy. I still grease mine when they go it and if they move..they move. No biggie.

 

This is the part I was wondering about. Good to know it's ok if there is some pivot of the bushing in the sleeve. Beats the hell out of squeaks.

 

yeah i was less libral with it this last go on my solo arms...major regrets. Never again. Should have just done what I always do.

 

Why vinyl over other materials? What are your first thoughts and impressions on it? I wonder how uncomfortable vinyl is on a hot day..

 

I would make sure the inside surfaces of the frame mounts are flat and smooth. Mine were all sorts of bent from years of wheeling, and gouged from where the washers previously contacted.

I would also highly recommend adding a grease zerk to your LCA. I try not to install poly bushings anymore without them.

 

East to clean and maintain? I plan on doing vinyl in conjunction with sound dampening. With the combination of the two im banking that it will be cooler overall on a hot day.

 

AC !!

Lol. My crawl box throws so much heat. My son noticed it right away. AC cant match it

 

Right after I installed the vinyl I sent my throttle body to Maxbore so I haven't driven it yet. I'm real happy with the way it looks and the quality, the vinyl is very thick. I also have factory vinyl in my 2000 Chevrolet and I love it. As long as I can afford it I will never have carpet in a truck.

 

Replaced the exterior front door handles. Drivers side Factory Toyota ($150), passenger side Cheap internet knock off. Of course the drivers side will get more use. I just wonder how long the cheap one will last.
Also added Sound Deadening to the inside of all 4 door panels. I can hear myself think while driving now.

 

Thanks there 17" ray 10's
https://www.tacomaworld.com/threads...-ray-10’s-17x9-w-3-5”bs.534302/#post-17158592

 

The first of what seems like many poly bushings showing up soon.


USPS lost my shock parts so those get pushed another week.