What Have You Done To Your 3rd Gen Today?

Can you post the link
Thanks

 

Added the front window tint today! $200 for ceramic tint at Trifer in Eugene, OR. Customer service was great!

 

Did @Hodakaguy's relocation of the spare tire lift so that I could get my new full size 275/70R17 under the bed. I didn't bend the tabs and it does come in contact with the drivers rear leaf spring hanger but is 95% out of the way and up.

Can't move it closer to the passenger side or it's way too close to the exhaust for my liking.

Here's the link to how he did it. I didn't take pictures of my install.

https://www.tacomaworld.com/threads...to-new-adventures.528480/page-5#post-17311994

Also installed the seatjackers in the front. I wish I hadn't waited so long, it feels way better to sit in already.

 

I asked about this when I got my xpel ppf put on. The guy quoted me $900. I didn't ask how many coats that was.

 

Installed the GFC cross bars mounts instead of the custom crack brackets I had to mount the tent. Added the beef bars. Put some finishing touches on the CBI T3 front bumper, installed the modified front runner recovery device mounts. Today was a good day.



Still need a little bit of trimming on the front bumper plastic. Turns out the bumper doesn't sit level, and my driveway isn't level. Makes these cuts very interesting..

 

But it looks amazing!

 

Technically last evening, but my DMM came so I got that installed. Ran a bolt through all the threads before I put the trim back on the truck just in case.

 

My local county library has a 3D printer and they only charge for materials by weight. I emailed them a Thingiverse file I found in this thread and they printed 2 caps for me. $3 and one day of wait time and I have 2 caps for my new rail. One fits great, one a little loose but worth a shot if they offer it in your area. I believe this is the file if interested. My two cents.
https://www.thingiverse.com/thing:4718243

 

I wonder how hard it would be to 3D print a bad ass grille……

 

I like it! Did you modify it so you can plug it into the bed Outlet? Also what are you doing for your water source?

 

Very hard... For one, it would have to be in multiple pieces since most print beds are not that big. For two, it would depend on the style of printer to get anywhere near a decent surface quality. Lastly, you wouldnt wanna know the cost of having someone like me (at work) print one of these for you on a semi middle of the road printer ($65k).

 

Installed around 2 square feet of left over Dynamat that I had from my son's car. I started early this morning to beat the heat but what should have taken an hour to do both sides took over 3 hours because I did not want to break any of the plastic fasteners in the fender liners. Hopefully, this will reduce some of the tire noise on the highway. I now have 97 square feet of Dynamat, Dynaliner, and Dynapad along with 55 square feet of closed cell foam and 12 square feet of open cell foam so it is a pretty quiet truck. None of the interior pins or clips were as difficult to remove as the fender liner ones and if I were ever to this job again I would buy a bag of new ones and drill out all of the old ones and replace them with new ones.

 

What kind of water pressure do you get from that pump when you use the nozzle?

 

Was wondering if anyone has done a tutorial (or knows of one) on removing the back (under the back window) molding/ trim on an SR by any chance?

looking to do the sound deadening back there.... right now it’s just sitting in a box.....

 

Installed 2017 TRD pro headlights. Such a noticeable difference

 

Looks good!

Aren’t 17 pro fogs Ridgids?

 

Got my Cali Raised 40” prinsu bar up and wired in. Added the lamin-x film for the yellow.

 

Yes. But this isn't a pro

 

Im confused.

You said you installed 2017 trd pro fog lights, which are Ridgids.