What Have You Done To Your 2nd Gen Tacoma Today?

No picture but I installed a flow master super 50 delta flow muffler on my truck

 

HDPE 0.07”

Allstar ALL22401 Black 0.07"...

$65 Allstar Performance ALL22401 Black 0.07' Thick 24' Wide 25' Plastic Roll

https://www.amazon.com/dp/B006K8HXGK?ref=ppx_pop_mob_ap_share

 

HDPE

Allstar ALL22401 Black 0.07"...

$65 Allstar Performance ALL22401 Black 0.07' Thick 24' Wide 25' Plastic Roll

https://www.amazon.com/dp/B006K8HXGK?ref=ppx_pop_mob_ap_share

 

Thank you! I’m really pleased how it turned out.

 

I finished the front wheel wells. Liners installed & flares put back on. I cut 2” off of the flares and 2-1/2” from the fenders. It took a lot longer than I expected. I thought I’d have all 4 done by now; but I don’t care. It turned out amazing.

 

I have the same one. I think it's perfect not too loud just enough when you get on the gas and it doesn't sound like crap like those old 90s hondas lol

 

I always wondered what 3rd gen headlights would look like on a 2nd gen.. I like it!

 

Almost finished the deadening/insulation today... But then of course... I measured wrong and ran out of black... had to order more.....




this mod....



Well at least I was able to tidy up some loose wiring and appease my OCD.

Hope to finish this shit next week....

 

Took it on a little 45 min. drive to my niece's house to look at her car. 2015 Chrysler 200 with a 2.4. Needs a motor (transmission) mount.
Why in the hell does Chrysler use external Torx? I don't have the correct size so I borrowing it from a friend today.
I also found a shortcut so as to not remove the battery tray, which is a PITA.

 

Hi there, looks good. Did you get the blue wrap from a dealer or was it an online purchase? Anyway looking to do the same. My clear coat is faded bad on the roof. Thanks.

 

Guessing you have the 4 cylinder? I ask b/c mine is in for a new frame and if it ends up needing an exhaust I might just get it done while it's there..was thinking I'd upgrade when that time comes.

 

Any word on the fender?

 

At the body shop getting painted.

 

Yes it did. I even had vibrations at highway speeds lately that were fixed. I went and got the tires rebalanced since I thought it was the tires but the shop told me they were fine.

 

I have a rotational squeak that is intermittent but when it does, the squeak accelerates as I do. Let off the gas, no squeak.

I greased all my zerks, no help. I changed my u joints and my carrier bearing 33k miles ago. Carrier bearing boot looks rough.

My setup is Bilstein 5100 on ome 885 coils w AAL. Thoughts? Time to do my u joints again?

 

Looks factory. Good work!

 

Picture of the carrier?

I think what you're referring to as a "boot" is actually the support rubber "doughnut" and if that's bad and your drive shaft has more than a little play it needs replaced.

 

Finished adding another leaf to my Dakar heavy pack to make it the 96r+ pack. Shes a big girl now . Also took the time to repaint and add pads and shims. Also had to get a new center bolt.

 

How are the output shots?

 

Could be a bad wheel bearing, i had the same symptoms as you and thought it was the center carrier on the drive shaft. ended up being the wheel bearing.

it was an embarrassing squeak too. the kind that makes people turn their heads when you are next to them at a red light.