What Have You Done To Your 3rd Gen Today?

I think the last time we had a rotary phone in the house was when we still lived in Georgia. We moved when I was 7.

She works at the hospital.

She can prescribe drugs, though.

 

We still use pretty old tech in Range.....

 

So honestly speaking I went overkill to start so I bought a Switch Pro 9100 and a PowerTrays setup right after I bought my 3rd Gen. This was mostly because I knew I was going to do a lot of wiring as this is my 2nd Tacoma and I love having lots of lighting. The tray gives the ability to add on without adding a rats nest of wiring like I did with the first Tacoma which I eventually ripped all the wiring out when I added a PowerTray to that one too. I have also since added an Off Grid Engineering dual battery setup and isolated all the accessories to the second battery.

Here's a pic of it. Probably could have done it a bit cleaner

 

crack your windows...lol

 

I like it! What color is that paint you used?

 

Is this better?

 

I have the same story as you- brought mine in 2/27/21 for the fuel pump recall and expressed concerns with the bubble. Advisor said that he’d look into it. I just have t heard anything back.

 

Greatly appreciated! I like the idea. I have a Barc Red Sport & wondering what these might look like on it. Thinking about a few inches below the "Tacoma" below the trim fold

 

Yes apparently it does. Found this site a while back.

https://www.oldphoneworks.com/

 

They are typically mounted up higher as an impact point to prevent door dings. You might double check before mounting them lower if car doors would actually hit that low or if they would hit higher up on the door. My sliders protect the lower part of the door.

 

Did the BHLM to my 2021.

Definitely worth the effort, especially on a silver truck!

M3 Work Round 10 by Michael Rickerd, on Flickr

M3 Work Round 10 by Michael Rickerd, on Flickr

 

You use a heat gun or oven?

 

Welcome. This particular model is meant to be on a flat surface right above the emblem. Per instruction. I was going to put it right below where the body protrudes out more but this model is too thick for the curvature. Sportwing has a thinner version for the lower body part. I also believe this one might/will protect from most/some vehicles and most four door sedans (rear wheel well door edge). Plus, I have the 2nd Gen running boards. You’ll be happy with their color matching. I can’t even tell it’s there.

 

I got an alien gear holster. It’s switchable, adjustable, and covers the trigger. Plus it’s an easy draw and sits at a comfortable/natural angle.

I bought one for my Glock and Sig M17.

 

Mine won't charge through the Otterbox on any Qi charger I have tried thus far.

 

Oven. If you search for my username in the BHLM thread you can find exactly how I do it.

Or, I can do it for you. Just let me know.

 

Nice, and what I'm looking to do. Can't find that specific Alien holster anywhere though. got a part number, or model number?

 

Same issue here when I got a new phone. With the slightly more protruding camera lenses on the iPhone 12 pro max the Qi charger would not sense the phone, with or without the case (Otterbox Symmetry). Worked fine with my previous iPhone 11 pro (case on). So I picked up an insert from Tufskinz and recessed the Apple Mag Safe charger in it to the point that the camera face just touches the surface and the phone sits flat on the charger. Still want to run the charger wiring back in to the console to hide it and connect to a hidden USB-C power source.

 

Lub'ed my UCA uniball's today. Had a horrible rubbing noise on and off, thought it was my power steering initially. Easy fix, got this:

$24 CRC Dry PTFE Lube, 10 Wt Oz, NSF H2 Registered Lubricant with Advanced Dry Film Technology, Plastic-Safe, Aerosol Spray (Pack of 1)

https://www.amazon.com/dp/B0013J84BY/ref=cm_sw_r_cp_apa_glt_fabc_KBVZ85P1WFZX7255FKPC?_encoding=UTF8

 

Check this place out.

Alien Gear | Holsters by Gun Make & Model - MidwayUSA