AZ Classifieds

Taco_Traplord93 is my IG name usually hit the trails here and there every other weekend.

 

Selling sig p320 axg scorpion 9mm. Brand new never shot. $1100. Comes with what you see.. 3 mags and awesome locking case.. Txt 480 619 9456 for fast reply

 

Set of four Yokohama MT G003, 265/75R16 (32")...bought in Oct2020 and have about 5K miles on them (~16/32nds)

Excellent shape, no damage/patches/plugs

$600...located in Gilbert

 

Alan, I'm running these same tires now. What made you dump them so quickly?

 

Because I'm a tire whore

Nothing wrong with them and they performed great, just went slightly bigger...

 

The first step is admitting your addiction.

 

Which?

 

Which tire? Maxxis RAZR MTs...

 

I’m thinking about getting the Maxxis RAZRs well, I’d love to know what you think of them after you’ve had them for a while.

 

Looking for a set of sliders for a third gen DCLB. Looking for some with top plates a 0 degrees. I’m moving to NC in August, so I don’t have time to wait for a set to be built. I’m located east of Phoenix, but willing to drive a bit for the right set.

 

It'll prob be faster to have a set built, than for a used pair for a DCLB to pop up.

You could also use the lead times to your advantage and order now, then have them shipped to your address in NC.

 

When are you leaving in August? Early, late? I just built these for @MR E30 and might be able to whip up another set for you. Just doing a little bit of traveling the next few weeks and have other projects planned out in between.



These are kicked up with a kick out, but I can do them 0 degrees and no kick out if you wanted. Only thing I haven’t done is top plates for anything. I’m sure I could, but I don’t have a fancy cnc plasma table or dimple dies or anything to make the top plates special. But pm me and we can talk

 

@snowsk8air2
Sir as soon as I get the truck back from being turned (it’s a Guinea pig for the system below) and can get my fat @$$ out into our convection oven garage I will get the truck ready for you to weld in the rear frame notches. Ever think about building exhaust systems?

 

Looking good, sounds like a plan, and nope for exhaust systems. If anything I’d do a one off for myself if I needed to some day, but that’s about it.

 

Speaking of exhausts- anyone have recommendations for AZ based shops who are familiar and competent with Tacoma exhaust re-routes?

 

ISO:

Complete OEM upper control arms, and strut assemblies.

Dont care if the parts are in terrible condition. Cheaper the better. Sold my stockers already, and now my old mid travel setup. Just need the capability to move the truck around, and roll onto a trailer before long travel gets installed.

 

I have stock ucas, shocks and coils sitting here. And rear leafs! All gen 2 not sure if that matters

 

Dropping these to $850 on craigslist, but TWers can take another 100$ off. $750 for barely used Falkens, cmon now!

 

I've been considering getting a set of sliders for the T4R, it looks so naked without anything there plus even at 6 foot 2 and stock lift I can't reach shit up there on the roof rack.

Do you do bolt ons or only weld-ons?

 

Good luck with that!
Most do $h!t work and will not put any connections so the system can be removed!
I know of two shops but one is far to busy building Lexus headers for overseas sells and the other is to busy installing LS’s in C10 trucks. I had to wait over 4 months just to have a resonator welded in from the one that’s installing LS’s. The owner that welded in the resonator welds look like a machine welded them.