Installed! Camburg Spindles

How about a 2" block. Make it level

 

I was talking about wheel spacers. The reason I want spacers and lift spindle is so it will fill up the All pro fenders. I am doing the rear lt first. Then the front later. Long story short Because that is how I want to

 

so what you are saying is you want glassworks fenders

 

Ya I would definitely go with Glassworks if you're running spindles with spacers. Look at my pic I posted and you can see how much just spindles kick it out.

 

I want the allpro glass fenders. I think they are a little cleaner.

​

 

Glassworks. looks the same to me minus the spray can paint job.

 

Are you running the stock springs in the front with the bilsteins? Where did you purchase your spindles?

 

^
Hey bud you have a 4x4 it looks like based off your info.

Spindles only will work for 2wd prerunners.

 

REALLY!? So I could get a 4 inch lift using spindles, and still have a factory ride? Throw on some 5100s at all 4 corners front set at 0 and it be even a better ride right. how do you level it out.

 

Yup, if you just install spindles the ride will not change.

 

You can't use those spindles on a 4x4 they are for PreRunners.

 

Alright Gents,
I've been up and down TW trying to find info about the Camburg Spindles. I don't offroad other than the beach, so mostly lifting for bigger wheels.
My main questions are:
1) Do I have to run 5100's all the way around? If so, what setting in front? (I've seen people set @ 1.75)
2) What rear setup?
I seen people running all pro leaf pack, deavers, but from their pics it look like they still have the BRO LEAN, which I don't want. I don't want spend a fortune on reservoir shocks for the rear or a custom leaf pack since I don't wheel.
3) Will an AAL and longer shocks work in the rear? (5125's) or lift blocks?

I appreciate the help.

 

1) you can run stock shocks with the lift spindles, it will give you a flat 4" lift with the camburgs and 3.5" lift with the TC spindles. If you want to go higher than the spindle lift with the spindles, then you can get billies and crank them up or get coil overs which is the best choice.
2) rear set up you can go all pro 3" lift springs or deavers or whatever to get 3".
3) AAL and longer shocks will work, but dont go blocks.

 

You don't have to run 5100's up front with the spindles, just keep the stock components. If going with an AAL try to get as much lift as possible to level it out, I know I've seen 2'' ones before that should get you pretty close.

x2 on no blocks. My brother had a leaf pack that started sagging and tossed a block in there, immediately took it off after one lap around the block. It was giving him a major vibration for some reason.

 

Thanks boys both your rides are sick!!!

Had a few other questions

blackhawke
If I go the AAL and longer shocks, do you have an idea of the length of shock I would need to go with? ie 5125's??

I plan to upgrade to billies in the future, but for now I will roll with the stock billies. Once I do upgrade if I crank up the front billies, I assume I would need to upgrade my UCA's????

1BlkT
Where did you get the Deavers? How much? I been searching, but just pulling up other forums.

Thanks again!!!

 

I got my Deavers from a guy on craigslist, they were pretty beat but I only paid $200. I then dropped them off at Deaver and had them re-arch them, new bushing and add another leaf for about $250.

New they are pretty expensive, I'd check out All Pro or even Alcan if your aren't set on any particular set yet.

When I first did spindles I went with an AAL just until I could find a good used set of leafs to switch to so I didn't pay full price.

 

youll only need new ucas if after the spindles, you crank up the billies to get 3" of lift out of them. but then youd have 7" of front lift. spindles keep the stock geometry. so by setting the billies to a lower setting shouldnt affect the need for ucas.

 

How much lift in the rear do you have? What size tires do you have in this set up? Thanks!

 

i have a 4x4 and cant put spindles??? daaaaaaaammmmmmmn!!!!!

 

yea