What Have You Done To Your 3rd Gen Today?

Problem with the SR (and SR5 I presume) is that there are wiring harnesses missing and/or wired differently. For example, when I wired up my dashcam I was hoping that the harness was tucked in behind the upper console but no such luck. I had to run the wiring down to the fuse panel. I'd love to have turn signal rear view mirrors but ain't even going to bother looking to see if the wiring is there. Toyota know how to save a penny or two.

 

I have a 2020 Off-Road and put the 2020 Pro taillights in. Everything fit perfectly. All the bulbs are just incandescent and the assemblies are the same shape. I’m sure that either the OEM Pro’s or the OR’s would fit perfectly in your 2019 SR.

 

Did and oil change, rotated the tires, swapped lug nuts for black ones, painted the little Toyota emblem on the wheels red and got a MESO key.

 

Fyi, follow thi thread.

https://www.tacomaworld.com/threads/footwell-lights-that-don’t-suck.735488/

 

That's it. Thanks my guy.

 

dang! that sucks. when i talked to them about install, they were saying they have limited times and they schedule them in advance. their ig says it’s also a newer service so i may have been lucky with timing. fwiw they had my truck for a full day, so it was all quite a process.

 

I did that last spring. Took over 20 minutes just to see the paint colour again before I dared bring it home. (my spouse likes the Taco as much as I do and she doesnt like it dirty).
The pic is what I found when I dropped my Pro skid plate after power washing the 1st time.

 

I'm guessinng i may see similar if i drop my skid plate. Temp is just below freezing here, so it's debatable if I should or not. but a quick power wash might be a good thing.

 

I’m going to do another wheel in blue stitching. I’ll let you know how it turns out. I also need to attempt leather on the shift knob. Anyone taken one apart before? I don’t really want to break it if I can avoid it.

 

Where’d you get these? I have a broken cap (missing the logo)

 

The same yellow fogs I purchased. Mine aren’t very bright but I love the yellow and they were cheap.

 

It actually works pretty well. Screws in to the bottom of the filter. No mess. Just add a hose to the bottom of it.

 

Bedside Molle Install.

https://youtu.be/pmGboa_pnws

 

No problem, no offense taken!

i believe this is the thread you’re looking for:
https://www.tacomaworld.com/threads/footwell-lights-that-don’t-suck.735488/page-15#post-26529345

but I don’t think they’ve been released. They said pre-order hopefully by early December.

 

Cool man. And yup! That's the one...following it now. I hate that there is no floor lighting too. Like you, I upgraded to the LED's and that helped some but at night the floors are a black hole. Drop your phone down there and it may as well be off to another rehlm..

 

Uhg. I feel like I should turn in my man card. Our 21 OR didn't come with mudflaps. Yay! I thought. (Removed them from every other truck I owned). Then tossed on some wider tires and 0 offset wheels. Yay! Looks great! BUT possibly growing older and tired off the constant winter spray down the side of the truck I decided to toss some OEM ones on...... at least for the winter/spring.

 

Yup, I took my stocker flaps off when I bought my truck in June and put them back on once the weather turned and the side of my truck started looking like some sort of abstract painting. I'll probably take them back off in the summer.

I did trim them up since the stockers look like four lunch trays slapped on the wheel wells.

 

Oh snap, that's a bummer. But thanks for letting us know, I was about to order from them myself but maybe not....

 

Ya, They are getting bob cut soon. I just want enough for the general splatter.

 

For sure. I may have gone a tad too short on the fronts since Im still seeing some splatter on my front doors, but it's WAY better than no flaps. Haha

If I'm being honest, I actually think they look pretty cool now that they're shortened up....but maybe that's just because I know I made em that way.