What have you done to your Tacoma today? 1st Gen Edition

Who makes this ditch light bracket?

 

Can find on Amazon and other places.

$39 XJMOTO Upper Hood Ditch Side Pillar Work Led Light Pod Mount Bracket Compatible with 1995-2004 Toyota Tacoma

https://www.amazon.com/Pillar-Bracket-1995-2004-Toyota-Tacoma/dp/B07VVKPTQB?hvadid=462937055979&hvdev=c&hvlocphy=9029301&hvnetw=g&hvqmt=e&hvrand=6654130500588914273&hvtargid=kwd-953746437962&hydadcr=2997_10903156&keywords=1st+gen+tacoma+ditch+light+brackets&qid=1637958521&sr=8-5&th=1

$17 samman LED Ditch Light Mount LED Pods Light Hood Hinge Mounting Bracket Compatible with Toyota Tacoma 2016-2020

https://www.amazon.com/Samman-Mount...a+ditch+light+brackets&qid=1637958521&sr=8-12

 

Found out that my parasitic draw problem was connected to my intermittent airbag light. Opened up the control module to find the capacitor died and killed some other things too. Found a used srs control module locally for $50 from a 97. After replacing the capacitors no more dead batteries and no more airbag light.

 

Had some good sunlight/weather today. So we decided to switch gears and paint some shit.




And when we mounted the new rack, I noticed the roof was hammered. Clear coat was pretty much gone, and I was down to primer in spots.

 

What’d you use?

 

Raptor Liner

 

Nice. I did that to my last wheeler on the rocker panels like that and it was great

 

So doing the clutch on my daily. It appears the PO lost or the shop did or something the transmission dust cover/inspection plate.

Not finding a PN or anything. Anyone ever replace theirs? or am I screwed?

 

This is for the SX right?

 

yeah. I found it. Toyota calls it a "rear end plate" so was weird finding it.


PN - 1136162010

Can't believe its been without one this whole time but..oh well.


Fluid was shit too. So hoping after rebuilding the MC and Slave, new fluids, new clutch, it'll not slip and I can actually floor it for once.

 

I did a headlight retrofit myself. Quiet easy to do actually.

I started with fresh TYC headlights from Amazon.

Baked them at 270 degrees for 10 min each, removed the lens covers, and the OEM bulb reflector shield.

Installed the projector housings.

Installed the lens back on, baked it again for about 10 min, and pressed them on with some channel locks.

Before:

After:

Forgot the cutoff pic, I have some aiming to do, and I'm parked on a hill so that's why it's kind of weird:

 

went wheelin and finished rebuilding my r150f in prep for my manual swap.

 

I had the same thing with mine. Bellhousing cover plate thing was missing and took a while for the dealership to find the right part that I was talking about because they didn't know what to call it either lol

Looks great. Clean look.
Nice to see just a simple projector install without all the halos or other fancy RGB stuff in there.

Did you upgrade the shift forks? Or get it annodized?

 

I believe there is a rubber trim piece for that as well. Maybe it's included.

 

I got the billet ones from marlin crawler, the 1,2 fork had some cracking.

 

Finally got around to installing my alcan leaf springs and ads shocks in the stock location.

 

There is indeed. Found that too. Bolts are a bit tricky but think I got it all.

 

I was able to get the fuel tank down and get the charcoal canister out. I also took the time to clean up some frame rust I didn't get to when I had the bed off last year.


I also may have discovered the source of my PO442 code

 

that will indeed do it

 

Good thing I replaced my gas cap 3 times haha