What Have You Done To Your 3rd Gen Today?

Thanks, here's the link of where I purchased it from. I used a promo code I found online and got it for $520 bucks.
https://truckandgear.com/bodyarmor/bda-87f0-tc-19339.html

 

RCI aluminum skids under the engine, transmission, and transfer case.

 

I've used this stuff a few times for random shit and it's strong.

Denser 1" Hook and Loop Tape Sticky Back - 5.5 Yards (16.5 Feet) - Strips Adhesive Heavy Duty Black Roll (1" * 16.5 ft)

https://www.amazon.com/Denser-Stick...1+Inch+Hook+and+Loop+Tape,aps,198&sr=8-3&th=1

 

No. Actually I had changed those out a couple months back.
Not gonna lie it’s “feels” stronger, but I’m paying a lot of attention to the exhaust sort of chasing the growl. It’s a manual, so it’s always a little more fun.

 

Took my new 21 trd in to fix the whistle noise from 55-60. Had to open a damper kit, hope it fixes it!

 

There must’ve been a shard of metal in the micro fiber towel, I tossed it on the vise, and now my whole dash has a little racetrack swirl across it. It’s not terrible but it’s there.

 

threw in a power tailgate lock, easy install but a decent amount of time under the truck placing zip ties which was a bit laborious. Put on a hatch mountain while I was at it because I hate my money.

 

Like literally your dash? Or just the guage cluster?

 

This conversation thread has me really annoyed. I'm stuck between saving to upgrade my shocks with maybe a lift, or getting a bumper/winch or hidden winch mount. All 3 are things I'd be able to use, but that's what makes it hard. So many good ideas. and all I did with my truck was drive the 24.6 miles each way to from work and be glad I didn't have to fill up with gas at $3.15/gal

 

Top of the dash. Light, single line scratch.

 

I was right there with you, ended up doing a 3” bilstien lift with freedom UCAs up front and ~2” OME rear leaf in the back as my first upgrade. My list is long and expensive, I suspect yours is as well. Just make it yours and whatever path you decide will be fine.

Im torn between a roof and bed rack system from up top overland or the southernstyle off-road front bumper with a winch…

 

I'll swing by 1's one day soon (maybe on a weekend) and you can check it all out. No need to wait for the next fire (although you missed a good one on the day after Thanksgiving! )

In the meantime, here's my build thread, if you want to check out any of my mods. Just be careful... this stuff is like an addiction, and it's hard on the wallet

https://www.tacomaworld.com/threads/jfanaselles-3rd-gen-build-and-adventure-page.699778/

 

You might be able to use a hair dryer to gently melt the scratch down and then try rubbing it with your finger so it's less visible. A heat gun would work too, but at a much faster rate.

 

loving that xwing top mount for the 8 gang. But, you really should upgrade those map lights. Those oem map lights hurt my soul now when I see them. The MESO led upgrades are tremendously better..

https://mesocustoms.com/products/ultimate-map-lights?variant=13238302638193

 

Thanks. I’ve considered something like this but was more stuck on using some sort of iron. Maybe I’ll give it a try.

 

Heat gun keep your distance (as much as you can) and don’t leave it in 1 spot- always have it moving, keep on low. I’d probably use a microfiber wrapped around finger instead just because you will alter the texture too much if your not careful. I did this to bring back grey plastic on the door panels (last truck)

 

Use rivnuts. You’ll still drill holes, but rivnuts will make the holes look OEM. Top photo is one of 2 rivnuts I installed in my truckbed to make attach points for my MOLLE panels. The panels use existing driver side cubby trim bolts for attach points but the cubby was deleted for 2019 leaving none, so I made my own.

 

right, now is when we love the FL weather.

 

Nice job.
That CRKT mount will let you tilt the knife up at an angle. Changing the screw locations on the belt clip to have the handle end come up a little will make it much easier to pull out incase you need it quickly while you are sitting in the driver seat. And, it will not effect the pull if you need it while you are standing next to it with the door open.

 

Yes the Weather is Beauteous this time of year.


Ordered a Trailgate Panel From Aloffroad with cup holders. Looking forward to having that addition to The Taco.