BAMF High Clearance rear bumper "Modular DUAL swing out"

I lifted mine up a bit then went from there

 

I mean.. I probably could use the forklift(s) at the shop.. but yeah.. mines a little different..

 

Yep forklift would be perfect for that.

 

I guess I just need to lift the rear enough to get a board or something in there, yeah? I can just lift off the 2 rear points then..

 

Looks like you can see the cap that's on the top of the sides so I think you can use the bottom of it as your line.

 

It does sit on top, with a very wide and large bulb seal mating it to the bed rail caps. I wasn't sure if I could get away with that or not. There's a little bit of the caps exposed still with the camper on.

Or.. if I opened the side doors on the camper and ran my straight edge through the camper (it's a nice flat surface with the doors open).. and added that extra height of said camper.. maybe that would do it as well.

 

I'm on the first batch who preorder the bumper, so i went with dual jerry can holder with propane mount. @JLee I received the goodies yesterday if it wont fit, can switch it to single can holder?

 

@JLee Do you know if the LifeSaver Jerrycan will fit in the Jerry can holders.
Here's their dimensions
349mm x 171mm x 476mm (13.75 x 6.7 x 18.75 inches)

 

Yes it should. the cans we have are from Jerrycan.com and are.

• (L x W x H): 6.5 x 13.5 x 18.5

 

i don't have a problem with the fuel side, but my spare kinda blocks the other side.

 

Is there a way to confirm the bumper was cut for 35s @JLee ? Before I get too far into this, just wanted to make sure. I cut my fenders and flares for my 35s months ago..

 

Was your measurement from top of bed rail to your cut line the same as mentioned in the 2016+ install instructions? 17.75"? Just trying to confirm my measurements. Think I can get away without removing my camper.

 

Mine also came undone. @RangerComa were you able to fit the 1/4 pop rivets all the way through the holes until the head was flush? Mine do not fit - hit the steel weld on the underside, so I’m wondering if I’m expected to drill a 1/4inch hole on both sides.

 

Where are you guys putting the tire mount for a 35?

Guess it's just going to take some trial and error for fitment of everything.

 

Need to add the tire mount for my 35, the Single Jerry Can, and my propane tank/mount. The Jerry can and propane mounts are a little confusing. I think I figured out the order and locations for the Jerry Can hardware. Also, I didn't receive any washers or back plates for the propane mount hardware (just bolts and nylon nuts). I'll need to source some fat fender washers for the backside/inside of the Jerry can mount.

I did notice (and this is from me not having any bedside supports for a while) that the last little corner of bedside material under the tail light.. is barely hanging on for life. It's cracked almost all the way through, and separated at the pinch welds. The vertical crack running along the crease, and another one barely visible running horizontal. Soon they will connect and there will be nothing to keep that section together. I hope to add some jb weld to the backside to deter any more cracking. Once I finish the bedside supports, it should help a ton. Unfortunately.. the damage is already done.. but like I said.. this was my fault leaving them unsupported for so long.

 

I have a 3rd gen but i can get you a picture tonight.

 

Should be pretty similar I'd imagine. Thanks.

 

I used these, they sit flush, no modification needed.

 

@XPOTRPR

Here's some pictures of how I mounted my 35in spare. I have it just centered enough so you can still see the passenger tail light.