1st Gen Lunchtable Thread - General Discussion

I made myself a dual NEMA 6-50R/14-50R for my welder and air compressor. Just as long as they aren't both running at the same time it's fine. Unconventional jumpers behind the scenes though.
Welder came with a 6-50R male end though - Harbor Freight Titanium - and I bought my own compressor cord to go in the other side.

 

The 95 is probably the best running one I’ve got. The 98 close second. 02 third… 01 still no done

 

NEMA 10-30R is what my dryer outlet is in my rental house. I just assumed it's what older homes had. I have an adapter to plug my extension cord in for my welder. I barely weld now since I have to leave the door into the garage open 2 inches for the massive extension cable.

 

well this bed popped up locally. if its cheap the flatbed idea is out the window. because this ones the correct color and even has the same stock graphics (the flames would need to go bye bye)

other photos show minimal rust. i'd be getting the inside line x coated.

 

That’s right it’s a really old type of 220v plug no one really uses anymore. My air compressor is from 1999 so it makes sense as to why it uses that.

 

I'm so happy someone recreated these beasts. easily the best sounding vintage racer.. 16 cylinders. 1.5l, 600hp with a supercharger...
https://www.youtube.com/watch?v=wNfaLTdR6Xg&ab_channel=BritishRacingMotorsBRM

https://www.youtube.com/watch?v=xMOeYDclFWQ&ab_channel=AshrafAbba

 

R

Remind me what these are for exactly.

 

It's about showing off wash and wax jobs.

 

The Camry group is surprisingly good though because the mods do a really good job

The ls400 groups are aids

 

When your cats get stolen you weld a pipe in their place than put that between the sensor and the sensor flange

bam... no check engine light

They used to be like 10 bucks though

 

I'm surprised you are not going to buy this complete truck!

 

@BartMaster1234 One of the best sounding Z31's.

https://www.youtube.com/watch?v=UkSmEyl4H5A

 

Doc lobbed me an Amazon gift card yesterday after that crazy shift as a thank you. Thinking of getting jack stands to be ready when i tackle this rear end on the slug. Does anyone have recommendations for jack stands on there? should i go with 3 ton ones?


Thank you in advance

 

I use 3 tons for just about everything, but they're just barely tall enough since my floor is all wonky.

I'd check the minimum and maximum height and see how that might work with your setup, not sure what the distances are on yours.


Safejack seems to like the omega brand bottle jacks, who also appear to make jackstands. I don't recognize any of the other brands i saw on Amazon.

 

You might also consider saving the Amazon card for weird shit you need quick, and get the jackstands locally. Theres always something I can't find locally and I need before I leave.

 

I’ve been really happy with these 6T stands, but they’re not cheap.

That’s 6 tons per pair, btw.

Hein-Werner HW93506 Blue/Yellow Jack Stands, 6 Ton Capacity (Set of 2)

$197 Hein-Werner HW93506 Blue/Yellow Jack Stands, 6 Ton Capacity (Set of 2)

https://www.amazon.com/dp/B0011O2RYQ?_encoding=UTF8

 

Hmmmm. Maybe. Girlfriend has some overland ambitions, could be a fun weekend!

 

Safety is worth paying for.

 

My HF stands haven't dropped... Yet

Though I did verify they weren't part of the recall

I use 3T stands for the rear axle or to hold up the driveshaft or hubs when doing cvs, etc. They're too short for using on the frame though with the 33s. For his slug they should be fine though