What Have You Done To Your 3rd Gen Today?

Those are the Predator steps. Many folks here running them. I'll have to measure how far they drop down. Not really sure. I don't do any rock climbing, just trails. I need the steps for my 4-11 wife and 5 year old.

 

I’ve seen a lot of people here talking about the predators. I’d love to know how far they come down. my wife is short as well. Need a damn ladder for her haha

 

History

*EDIT

Looks like you beat me to it

 

I made this last year for pi day. No measurements, eyeballed it all. Made it a rectangle to be contrary. Tasty pumpkin pie.

 

Saw them live in like 96? Worth it

 

That’s awesome!

 

Oddly enough that is not how you determine the volume of that pie.

 

There are plenty of pre-drilled mounting holes on the panels, so I’d just do the same as I did for my rooftop Pelicans- drill them, then add a bolt with a fender washer & rubber washer outside, then a rubber washer & fender washer inside, and secure w/ a nylon locknut.

 

Love the truck! You and I have similar tastes.
I ordered a Avid front bumper guard at the end of January. I emailed Brandon yesterday and did not get a response. I am wondering what the lead time was on yours?

 

any idea if you need 2 separate cat shields going this route?

 

I was at these two...........

Devo - Orpheum Theatre (Audience audio. Boston. MA. 11/11/82)
https://www.youtube.com/watch?v=TeyIXB6My1o

Devo - Boston, MA - Jun 27, 2008 -
https://www.setlist.fm/setlist/devo/2008/bank-of-america-pavilion-boston-ma-23dbc0d7.html

And their still touring.........
Wednesday, 18 May 2022
The Rooftop At Pier 17, New York, New York, USA
Devo
Venue capacity: 3400

 

I see what you're talking about, but...it doesn't bother me. It's better than looking at chrome.

 

Do you do and sell custom reflective decals?

 

i don’t, I just use a cricut and make them. What are you looking to do?

 

finally got around to installing and wiring up some switches. still have not got the mounting brakets (or made them not sure yet) for light bar on the back and the air compressor so they are not hooked up but i did a shitty fab on a bracket to hold a breaker fuse holder and relay holder. there are some things i learned and will prolly do a 2nd one with a few improvements.


One thing i need to work out tho. the bottom independent light. i read i can tap into the brown wire that goes to one of the things already right there so you can have the dim capability's.. it does not dim tho. also when i have headlights on it turns bottom independent light off. So im going to have to search through the forums and see if there is a solution before i start a independent thread.

 

if she's 4-11" let me guess... you are 6'5"

 

Supposedly Dim is on the negative Don’t know if that’s the same wire you’ve tapped or not

 

took this from a TW thread i found on google

used 3 for ground and 4 for pin 6 on the otrattw switch.

 

Yea I think I could squeeze them in together. The wife would like another Miata as much as me if not more.

 

Pulled the rear seat backs and cab panels, installed

Siless Hybrid 3in1 200 mil 36 sqft Car Sound Deadening mat - Butyl Automotive Sound Deadener - Noise Insulation and Vibration Dampening Material

Siless 200 mil mat on the rear cab wall and area under the rear seats. Wrapped a piece of 1" foam pipe insulation over the cab vents to absorb sound but still leave a gap for airflow. Also lined the side panels covering the rear pillars and the rear panels. Wish I had done decibel readings prior to so that I could see the true impact, however this did make a significant improvement and to me was well worth the effort and cost. Will be doing the doors, floor and roof as time allows over the summer.