What Have You Done To Your 2nd Gen Tacoma Today?

Snagged a Maxi Trac awning from Napa. These things have been sold out for a while. I checked every day for a month hoping to find them in stock. Yesterday I timed it just right and my local store had a few in stock. Worker at the store said I was lucky because they found a few in back. They sold out in minutes. Word is, this is the same one as the ARB that runs about $400. I got this for $130. I made some extra brackets tonight and will install tomorrow. It’s a 8x8 awning.

 

Oh hey, good call. I just checked my local NAPA and they had them in stock for same day delivery. I ordered one with a 10% off coupon, it should be here later today. Now I need to look at an actual roof rack for the AC - I keep putting it off because I like driving 80mph on the highway when I can, and fear the wind noise will out-perform the two layers of deadening on the roof.

 

Installed my Cat Shield yesterday. And while under realized , I should do a under body wash. So that’s happening this weekend. Thanks to GetCatSecurity !!!!

 

Pulled engine on my 06 taco to reseal the upper oil pan, change clutch and pressure plate, changed timing guides and tensioners, also thermostat and now it runs like new!

 

Nice! Best bang for your buck awning. Others in this price range are at most 4x6 from what I found. That much sound deadening? You're good. I barely notice the noise on the freeway.

 

Nice I have a 2.5” ome lift too with 265/75/16 tires. What did you do to fit 285’s?

 

265/75R16’s for life

 

I know plenty of people swap in 1 tons but to swap in a 1500 axle you would effectively be doing all the same fab work with none of the added strength of a 10"ish ring and big pinion so I'd say it's probably not worth it over 1 tons. Plus unless Chevy uses the same rear ratio you'ed be regearing it or your front to match it assuming it's even possible.

Also the Chevy's while they use the same wheel bolt pattern are lug centric flanges not hub centric flanges so you may have wheel fitment issues or balancing issues unless you had custom shafts turned and at that point you've done everything to swap in a one ton, same time and money sunk with negligible benefit.

About guaranteed it's cheaper to fix what you got already if you have a E-locker 3rd (it's usually the electric motor assembly which I have rebuilt some before) but if you wanted to try look up the WMS (wheel mounting surface) width dimension for whichever axle you're considering.

 

Put on a new tonneau cover from truxedo today. I had a hard cover with struts that came with the truck but it was impractical. I loved the look but couldn’t haul anything.

I’m picking some 8’ 2x4’s on Sunday, any advice for securing them in the bed?

I need to get some more tie down points for the back bed floor. Which should I order?

 

Changed the headlights back to the stock style, put antenna brackets on, needa get the coax cables ran now, get rid of the double din, order and install a ham radio, then tires in the next couple of weeks


maybe a new grille too

anyone ever paint the scoop insert black?

 

Go with vinyl. Easier to switch back if you don't like it.

 

Maybe I’ll plasti dip it for a minute

 

Black Hood Scoop Mod

 

I like it

 

Put in some dual colour Meso map and dome lights. Also threw on some spotter mirrors.

was going to put on some VLED footwell lights, but apparently Mesos and VLEDS don’t work together….

 

73’s 73’s

 

Well


You lost me

 

Lmao always say that sarcastically, 73’s

 

I ordered on Monday and received it today, Friday. They even included a nylon pry tool. As has been mentioned before, I only received the driver side multi-switch. Still waiting for the passenger side.

 

Mine just arrived. Free shipping, four days.