What Have You Done To Your 3rd Gen Today?

You got the front off also?

 

found a deal on these for $280

 

I installed the Red Rock cold air intake kit night before last. Drove to work yesterday, and on my way home last night the CE light came on. P0101, P0170, P0174. Stayed up late after getting home, and put the stock system back on, reset the light, and haven't had anymore problems thus far after a test drive and all day today. 0/10 would not recommend the kit... I shoulda heeded the warning from Scotty Kilmer, lol.

 

Installed a 12v/USB receptacle in the bed for my rear facing dash cam. I've been meaning to do this for a long time. It was previously plugged into the 120v bed outlet and I would turn the converter on every time I drove the truck to power it.
Now the camera will turn on automatically with the ignition. 10 gauge wiring back to the battery going through a relay that's triggered by the 10A INJ fuse.

It's just mounted with velcro for now, good enough for a Monday. If it stays put I'll just leave it as is. I would like to find some blank covers for the unused holes, though.

 

Do they have added camber built in? Any chance you took a picture beside the shock arms?

 

im not a photographer. the suspension forum has a thread about them, enjoy your research.

 

the pic it shows some but in real you cant see it

 

removal of visor stickers:
heated the visor up with a small space heater, or

can use an iron by covering sticker with old tshirt
worked a corner up -fingernail-enough to start peeling slowly,
after sticker gone glue residue left so,

put a clean piece of t shirt over spot and ironed it for 15 - 20 seconds,
one sticker had more glue so re ironed with clean piece of shirt a couple more times till it looked good,
the glue will stick to the t shirt when heated......I had 7 decals on my visors

 

Did you figure out what the root cause for the errors were?

 

what did you use for the camera mod?

 

Sweet. I don't have anything to power currently, but I was going to go with their switches when I need them. Thx.

 

Ordered the cargo light switch and 3rd tail light. Now I either dremel a cut out from my dash panel or search for one that accepts the cargo light switch

 

The screen is black and I do notice it when checking my rear view mirror. I have a big roll so taking the screen out, painting and then putting new screen on shouldn’t take too much time.

 

LoL
They already slam the doors when the enter/exit the truck.

 

ROFL
I had a buddy who slammed the doors so hard on my vehicle, for safety, I felt like I should have re-torqued every nut and bolt on the vehicle after taking him anywhere.

Actually that was a bad memory, took me about 2+ years to break him of that. Looong time. I couldn't believe it.

 

Gotcha. Gives me an idea of what in for. Probably will take me a bit longer with just hand tools. Appreciate the info.

 

i only used the impact to take the tires off and a few bigger bolts. didnt save that much time. For sure the pitman arm puller is a must for some of those bolts. (steering rod and upper control arm bolts)

 

$20 Nilight 50044R 5 Pack Waterproof 40/30 AMP Heavy Duty 12 AWG Tinned Copper Wires 5-PIN SPDT Bosch Style 12V Automotive Relay and Harness Set

Nilight waterproof automotive relays

$15 Custom Accessories Compatible with Smartphones, 18003 12V Dual USB Under Dash Mount, Black

12v dual USB power block
Add-a-fuse from O"Reilly's and some #10 THHN from Home Depot. I already had plenty of insulated butt crimps and misc. stuff lying around.
Made a harness with this: 1/4" expandable PET braided sleeving and some cloth tape.

 

Ok. I'm sure I could borrow a puller for the job since I don't own one. Lots of auto parts stores loan them out as well. I've got a few more videos to watch before I try and tackle this. Thanks for the tip.

Edit. We should have hooked and I could have helped you and learned a lot...lol
Hind sight

 

Did you get the kit for the rear seats as well?