What Have You Done To Your 3rd Gen Today?

Is it the front and rear camera setup or just the front? Currently have a

$190 VIOFO A129 Pro 4K Dash Cam 3840x2160P Ultra HD 4K Dash Camera 8MP Sensor GPS Wi-Fi, Buffered Parking Mode, G-Sensor, Motion Detection, WDR, Loop Recording

VIOFO A129 front camera powered by a Dongar mirror adapter (works great), but I'm curious about the option of mounting a rear-facing camera too. VIOFO has that option also, but I like the "integrated" look of the FitCam X. TIA!

 

Leer and century make them for the studs on the roof of the bed cap

 

Same here...I logged my MPG by hand for about a year... I was running the stock 245s and getting about 24 mpg. I switched to 265/75/16 and did hand calculations for about 8-9 months after getting new tires. My manual calculations match what the truck calculates ..which is roughly 20-22 mpg on the reg .. I trust what the truck says....I'll be getting new tires in a little bit, so now I'll go back to doing manual calculations for a while...just to see if anything changes

 

Pretty sick bike .. flame paint job isn't my thing, but that thing looks setup pretty good

 

Leave it off. It was the only badge my SR came with. I ripped it off immediately.

 

I installed the thick Millercat shield and that went on super easy! I live in MD so cat theft is a thing here. I never had this problem in other vehicles but the cats are super easy to cut on this so it felt like a good idea.

 

It is the front and rear combo with 4k front camera

 

It is not BSM compatible

 

I’ll pass along the compliment, when he got it it was all chopped up and a mess. He’s done all the work himself and absolutely loves that bike. Said he will never sell it. Funny you mention the paint job, he was worried the shock oil would ruin the paint job when it blew

 

Load 3 of the weekend pulling downed trees out of woods, ripped my driver side rear mud flap off which means new chore for tomorrow

 

New leaf springs are in my future, low rider by war kept going through my head while bringing load number 4 down the driveway

 

Neutralize it with baking soda and water and it should be OK unless it was a fresh paint job and not fully cured.

 

It's been about 4 years since I ceramy coated my truck.
Just got done wash, buff out and coated again.
Griot's Compound and Nano-Bond Ceramic Coating Kit. Super Good Products.

 

Coated my undercarriage/frame/panels in surface shield. Noticed about four or five tiny rust spots on the front end of the truck and just soaked them and everything else. Good to go for winter.

 

Nicely done. What happened to yours?

 

I just have to power wash and touch up my frame before winter. I have the typical very minor Adirondack North County rust. I am going to use Eastwood Rust Encapsulator Sealer this time.

 

I washed mine if that counts?

 

This weekend I installed OEM tie down D rings that I ordered off Amazon (Toyota Tacoma Cargo Bed D-Ring Pair 2005 06 07 08 09 10 11

$37 Toyota Tacoma Cargo Bed D-Ring Pair 2005 06 07 08 09 10 11

https://www.amazon.com/dp/B004W9ABC2). Put them on top of the wheel well. I have bed rail tie down points but when I put my kayak on top of my bed rack, the rails bent upwards. After I installed them, I took the kayak out fishing. These worked great. Felt more secure. Now I just need to find tie down ratchet straps that do not become loose.
And today we packed up the truck and headed to the beach fishing. Didn’t catch anything today but we had a really good time.

 

This thread sums it all up, start with the last post InThePlains sums it up.

https://www.tacomaworld.com/threads/3rd-generation-coolant-bypass-leak.797196/page-6#post-29096412

 

I think, all years all models.