What Have You Done To Your 3rd Gen Today?

completely new wheel or wrap kit?

 

Took her to the 4WD shop to check and re-torque everything for the 700 mile inspection after The lift. And to drool over some more shocks although I’m really happy with my 5100’s.

 

Nice.

 

This is the SSO Hybrid without the wings, the light bar is the 32” caliraised with their bracket.

 

I did the same and I have the drivers side that just isn't where I want it to be. I think when I get the opportunity (soon) I am going to pull the front seats and redo the covers and get a tighter fit. Yours look good, that's why I asked.

 

Thanks for the info. I just ordered a set of Caliraised light bar brackets. I noticed their brackets use the inner bolt vs the Rigid and Baja Designs brackets use the two outer bolts. My other concern will be if the light bar will interfere with the winch switch. I guess I will find out when the new brackets arrive.

 

I unbolted our front seats to install Clazzios. Didn't need to remove them completely though. By tilting them forward and backward it was pretty easy (well, that's a relative term I guess ) to pull/tighten the covers and run the tie-downs.

 

What brand of rabid squirrel do you use to clean the cluster lens?

 

Over the weekend I installed a Goose Gear rear seat delete. I had the factory sub but ending up removing it but I modified the bracket and kept the amp. Once the the seat delete was installed, I decided to run power to the back of the truck for my fridge and other accessories. I had a piece of 1/4" HDPE laying around the garage and with some 1/2" spacers, it turned out to be a great place to mount the fuse block. I also installed a Blue Sea Accessory Panel mounted in a Rago Fab 12v Accessory Panel.

 

so, mud gets slung on the OR fender flares, tried car wash, high pressure wand, and even hand scrubbing, but there is still spots where the mud was.

happen to anyone else? solutions?

prob going to happen to flaps too

maybe some different type of mud? once was in some red dirt area

 

Installed the original Sport cheese grater, blacked out though, grill. When I installed the warn bumper the bar is in the way of the front camera. Luckily, but angrily from the wife, I had bought the other grill for 20$ and installed it 5 years ago.
So, a face lift!

 

My wife has called my truck now, her truck and asks why I do things to it, and then she drives or rides in it and gets it. Where did you make the cuts in the chin strap for that bumper guard? I like it

 

Thank you! I did take my time and used a trim tool to make sure it went in well into the sides. It isn't perfect but it's as close as it'll get without taking them off.

 

Spent the weekend in the 4x4 area of Carova Beach, (OBX). Really appreciated the ARB (single) compressor and the SpeedFlate setup I put together a while ago. (Ran a line to the rear bumper). Worth every penny; saving us from the constant air up/down lines everyone else was dealing with when heading into town. From 15 psi to 29 psi in under 6 minutes.

 

You sure that’s mud… could be transmission fluid or brake fluid. Idk if your flares are textured but this stuff does great on my plastic tonneau cover, removes hardened sap and weird stuff. A semi soft brush will get into any valleys.

 

You might try 50/50 distilled vinegar and deionized water in a spray bottle. Or even some Adam's tire and rubber cleaner.

 

I need those TRD PRO inlays for the bed, Got a link?

 

Doesn’t that void the warranty?

 

Good for you on the payoff!

I've got a gas cap holder and locking gas cap!

No CEL errors in over a year of install.

 

Looks like you were angry at that license plate. I made brackets for that.