What Have You Done To Your 3rd Gen Today?

Personally, I never load anything into there that I wouldn't be comfortable with getting wet even with the cover. I also utilize Rubbermaid bins for storage when camping which works great for keeping food dry.

 

Good to know, thanks. I'll remove mine while they're still new and replace them with SS. I did spray the threads with WD40 before I put them in but I'd feel better with SS now. Tnx!

 

I recently had to remove my old one that was going to crap. Where did you get yours?

 

Amazon

$60 Factory Crafts Blackout Hood Graphics Kit Vinyl Decal Wrap Compatible with Toyota Tacoma 2016-2020 - Matte Black

https://www.amazon.com/gp/aw/d/B076XVRMX2?ref=ppx_pop_mob_b_asin_title

 

You forgot the rake.

 

My glovebox/passenger door, can pinpoint that spot. just makes the truck seem 20 years old.

 

Whenever someone rides with me, after they get out the seat belt is twisted 90 degrees and makes a rattle until I flip it so it lays flat.
Hope it’s something simple for you!

 

I've had the MX4 on my truck for a year. The two main places I have had water get in was at the front of the bed (they give some soft rubber tabs for the edges of the front rail which help tremendously) so look for any little gaps there. Also around the tailgate - this isn't from the cover but from gaps around the tailgate. I used a tailgate seal (helps with dust also) and some of the front rail weatherstripping in the MX4 kit (that you don't need for the 3rd Gen) to seal where the top edges of the tailgate meet the sides of the bed. The high pressure wash wand at the car wash can also squeeze some water in. So it's not fully water or dust proof but what gets in has not been an issue for me.

 

Funny you should mention that. I have had the same issue. Today I took my truck in for service and heard a rattling noise afterwards when I was out wheeling at Hollister Hills. Two issues, 1 the dipshit tech put the oil change access panel on backwards….

The second was I started hearing a rattling noise underneath while I was ascending a black diamond trail and had no room to turn around, let alone stop and check. When I got to a spot where I could get out and check I discovered a bolt was missing where the engine and transmission skid meet. Needless to say my day was done since I didn’t have any extra bolts on board to remedy the issue. When I got back to civilization I was able to pick up up a bolt and washer and fix it. My prior service at Victory Toyota they removed the skid plate to perform the oil change. Apparently these yahoos didn’t use any locktite. Like they say, if you want something done right do it yourself!

 

Had the same issue as well as some squeaks in the same area. When I pulled the speaker cover to install DS18 tweeters I found that the mount for the auto-headlight sensor was loose. So I inserted a few thin strips of rubber insulation around it as well as along the edges of the grill, in particular between the speaker grill and the edge of the window trim, all below the surface so isn't visible. No more squeaks or rattles. I don't recall where I got the material, but it's something like this stuff so it's easy to cut up:

$11 MATNIKS Solid Neoprene Rubber Sheets Black 6x6" by 1/16 (Pack of 3) for Pipe Insulation Plumbing Gaskets DIY Material Supports Leveling Sealing Bumpers Protection Insulation

https://www.amazon.com/6x6-Inch-Neoprene-Plumbing-Material-Protection/dp/B018H9CCPG?th=1

You can find something similar at Home Depot or your local auto parts store.

You could probably use some 3M trim adhesive tape too.

 

New TacoNet bed net

Just need a 3rd bed rail near the cab to use it correctly. I get mine via Amazon.

https://taconets.com/products/toyota-tacoma-cargo-net/

 

PICS

 

Need to put it on tomorrow hopefully. Weird thing is their black carabiners turn green in the sun.

 

Maybe they have a zinc plate.

 

Finally attached the Stant locking gas cap. I waited enough time for the cap from O'Reilly without the "S" on it to throw a code, but it has not.

Now .. committing to Diet Coke or Diet Pepsi ...

 

My rattle in that area was the speaker cover.

 

Never seize. And an old mechanic trick. When tightening the screws hold the pressure on them for a few seconds. Mine are still good

 

This fits 2016 - 2018

2023 Latest Updated Navigation SD Card Fits Toyota GPS Map Update USA Canada 86271-0E075 Work for Prius 4 Runner Avalon Camry https://a.co/d/2mOc4dR

 

I get the same thing. Have to properly adjust them.

 

Is there a fix or a sulution for this? I have same issue with my Kenwood, with rear camera...