What Have You Done To Your 3rd Gen Today?

Lol yes, According to the stealership's service yahoo's with their air impacts on everything they touch.

 

Post #274819.

 

Yes one of the first mods i did to the truck, also adds some additional tie down points, cheap insurance for the bedside. Topper is 2-300lbs so its a decent amount of weight especially rocking and bumping offroad

 

+/- 23.625%, yes.

 

I'm going to have nightmares about this for a week now. I'm sorry, dude. That hurts all the way over here.

That looks so choice! This morning, the wifey turned to me at breakfast and said, "I think it would be a bad idea to go on our trip to the four corners before you put some sliders on." I'm not an idiot. Gonna call RCI on Monday. If they don't have it in stock, I might die.

Those cargo boards are genius. The net is to keep the sheet goods held up by the boards from sliding into the road, I assume? I'm gonna have to copy you!

 

I was gonna get all old-man about it and complaint about that option, but you're right. The thing is priced really nicely, so I should just bite the bullet and move on.

 

Took off my soft topper and put it back in storage today, I only run it in the winter time to keep my ice fishing gear protected. But this year we didnt really have much of a ice season, I only got out twice. So tonnaeu cover went on and I put my cool boat sticker on that my mother inlaw got me for christmas.

 

Gave my Tacoma a much needed wash and detail today. Every time I had wanted to wash it recently, it was either raining or was going to the next day. Hopefully I can keep it clean for at least a few days!

 

Installed the K&N FIPK (minus the hi-flo filter) and the TRD Intake Accelerator to my stock intake components. Also removed the secondary charcoal filter in upper air box for less restricted air flow.

Why did I do this and not one of the other 100 options? Bc the stock air box is perfectly suited for my needs, but with some light modifications. Also, the TRD Performance Intake uses essentially the same parts to achieve increased air flow and increased “performance”.

Project total cost was approx $130. Performance gains will remain unknown and left to wild speculation. MPG gains have netted me anywhere from +0-1 MPG.

Am I happy I did it? Absolutely! The engine bay looks nicer (which doesn’t matter), the truck sounds a little cooler with WOT (doesn’t save gas), and under normal driving conditions nets me better fuel economy.

All in all, I’m very happy and recommend this upgrade to anyone looking to mimic an “OEM+” build. Parts and numbers listed in pics below.

 

Looks good! Enjoy while it lasts.

 

Thanks! I hadn’t thought about using the cargo net like that. I will be strapping anything of substance to the existing anchor points in the bed.

I figure the cargo net should be good for some smaller goods. I plan to add more quick fists or other small tie downs to the cargo boards for bins and other organizers in the future.

 

How the HECK did that happen? [I'll read on, 55 more posts...I'm sure you have answered this one.]

 

Started making my blackouts for my truck bed. Need a surf trip soon so need to finish these asap. Learning to sew will suck

 

Installed the Rago Fabrication CB antenna mount. Wire wheeled some of the powder coating off underneath (the mount is SS) to ground the antenna.



Capped off the coaxial connector for now until I run the cable and install the antenna. Started raining so I called it a day. I’ll probably install the CB tomorrow morning.



Gonna have to “feather” down the powder coating a little. It rubs the tailgate when closing it. This mount is pretty stout and should last a long time.

 

Nice looking truck.

 

CaliRaised cat shields. First one was a learning curve. Took me over 10x longer than the 3 minute YT video. I had to completely remove the diagonal brace in order to get the screws to line up and thread in properly, but once hand-started they tightened up without a fuss.

 

Thanks for the great write up. Your dog’s face cracks me up.

 

Thanks. He was a wonderful dog. I lost him last month.

 

I finished installed a new bed cover and took wife for a ride shortly after only to have her tell me smells musky in here, you must have a water leak. Sure enough I did have a leak in the rear. Both rear sides carpet was damp. Went to work today (I'm a tech) and pulled rear seat bottoms and rear portion of carpet up, took all day to dry carpet and insulation. I'm pretty sure it's my 3rd brake lamp leaking. Is this common on 3rd gens?

 

Dang, sorry to hear that.