What Have You Done To Your 2nd Gen Tacoma Today?

Had a K&N airbox and filter on my 2016 Sport V6 for over 5 years. Never had any issues with my MAF on that truck. I just hated the noise it produced. Had a K&N intake on several cars over many years, including Z28 Camaros, trucks, other cars and my kids 2011 Shelby Mustang, and I never had any issues with any sensors of any kind. I think some people use too much oil which could be the source of their problems.

 

This was a pretty large amount of work, but it’s different. May not see another like it.

TRD knob off of eBay. Said it was for a Camry or Avalon. Couldn’t see the bottom, where it attaches in the photos. Took a chance on it. Anyhow, it is similar to the 3rd gen Tacoma knobs where it snaps onto the shifter and then the boot snaps on the bottom.

I filled it with epoxy, built epoxy up over the bottom. Drilled and threaded inside with 8-1.25 tap, sanded bottom area round and smooth.

threads right onto the shift lever and looks pretty dang good IMO.

 

TheQuisto, I had my OEM chrome grill painted at the dealership when I purchased my truck in May of 2012. I spoke to the “paint guy” and his only concern was how well the paint would hold up to road debris like small rocks etc… He recommended he adjust hardener ratio to the paint and I agreed. I think I paid under $100 for the dealership to paint match my spruce mica and today it still like brand new.

 

there is no point to the higher cost of a K&N, not including the drawbacks.
OEM filter, done.

snorkel precleaner or cowl intake mod results in less dirt.

 

Pop&Lock installed today. Pardon the rust, it's from the last guy. It's the

$122 PL8521 Pop & Lock – Power Tailgate Lock for Toyota Tacoma, Fits Models 2005 to 2015 (PL8521)

PL8521, so it uses the stock handle without a keyhole, which I like. Sort of stealth lock, and about half the price of the one that uses a key. Thank goodness for garages, because we're getting dumped with snow today in MO.

 

Long time lurker, first time poster. New grille, headlights, and running boards.

 

which running boards are those?

 

I’d like a set like the black ones. Is there a part number on them or are they stock steps?

 

Put in a safety cord just in case something fails you will be able to get the tailgate open manually.

Edit: Pop N Lock PL8521 Install With Emergency Release

 

Almost no chrome left inside. Trim piece for the shifter will be here tomorrow.

 

After 7 years with the AFE Magnum intake, the silicone couplers were rotting. They're single ply, so it's not surprising. I replaced them today with 3 ply and t-bolt clamps. The worm clamps were digging into the silicone. If anyone is looking for replacements, the dimensions are 4" ID x 3" hump and 3" ID x 3" straight length. I bought mine on ebay. They were cheaper than Amazon with tbolt clamps included.

 

Installed a Pop Lock. Now I'll only worry a little about my Yeti coolers.

 

@Oregonhillbilly

I like that….

Went a different route when the leather on my shift knob was degrading. Had to find the correct thread adapter 8mm-12mm, but I’m happy with how it looks.

 

Replaced 227k engine with one with only 130k on it. Oh and a supercharger.

 

Got around to installing my cowl intake before all the rain hits. Really nice kit from @dpele

 

Hell yeah!!!

 

finally trimmed my flares and swapped from spc to jba...still need spacers

 

Sick yoter. Looked even better in person when i bought those tails off of you last yr. Wish I'd taken you up on those trd seat covers tho

 

You’ll never go back!

 

I hope not lol