285/75R17 Perfect Size on 3rd Gen

what size lift are you running in that photo?

 

Has anybody compared geolanders to wild peaks in person. According to Yokohama website the geolander is 1/2” narrower than the wild peak?

 

Would someone be willing to measure to the fenders (front and rear) that has a 2.5” lift in front, AAL in back and 285/75/17 tires? I’m trying to figure out if I’ll clear my garage door. Thanks!

 

I've seen a handful of people here running JBA's with .75-1" spacers on 0 offset wheels to fit this lovely tire size, anybody have any luck clearing JBA UCA's with a 17x8.5 -12 wheel (seems like the equivalent to a .5" Spacer on a 0 offset wheel)? I checked JBA's website to get a rough estimate and based on the 35x12.5 tire needing 4.25" BS the 4.28" BS from a -12 seems as though it should?

 

Wellllllll, after reading this thread for a month or so I finally pulled the trigger on a set of Geolandar MTs in 285/75/17 with some 17x8 0 offset wheels. Currently on the same tires in a 285/75/16 on stock TRD OR wheels with spacers, and 6112s up front. I seem to have a ton of space with the current setup and I've already done a CMC and pinch weld, plus a little cutting. I think I should be ok with the 0 offset, tire is nowhere near my UCA (Camburg). Cant wait!

 

Toyo AT3s in 285/75/17s

 

These things make my 33s look tiny

 

I felt the same, major difference!

 

I have the same tires/wheels on Fox 2.0 with a JBA uca at 4.5 caster on my 2021. Now I just need to heat gun, but it's low priority right now.

 

285/75R17 Yokohama Geolandar M/T
SCS Ray10 17x8.5 -12
OME lift w/ SPC UCAs

 

I just noticed your front fender tire cutout. That's slick as shit. I love how that looks like it was meant to be there and how completely subtle it is. Did you experience any issues with the cut? Do you have a template or just mapped it out in erasable ink?

 

Holy hell, I didn't realize these guys are 10 minutes from where I live.

 

Oh yeah ... that right there is the stuff

 

Love it. Black rhino chamber wheels 17x8. -18 offset, Bilstein 6112 and camburg uppers.

 

Put these on 2 days ago. 2” lift, 0 offset methods, stock uca. Cab mount chop has been done. Tires will rub a tiny bit up front but nothing to worry about. Caster is set at 3. They get close to to Uca but don’t rub.

 

Thanks bro I wish they come with V-Cut from factory looks way nicer IMO. No issues at all, did it with a friend using a Dremel and some tape to mark the line. Also used windlace on the trimmed edge for that clean look.

 

What gear set is everyone running? 4:88 or 5:29. I’m stock apart from jba’s, nitto 285/75/17’s but plan on getting a leer shell and towing potentially a small boat or one jetski.

 

You’d be right. I am specifically running JBA’s with .75 bora’s to fit my 17x8 0 offset. I’ve already rubbed the paint off the UCA in one spot until I added the spacers. JBA should update to have the proper specs for 285/75/17.

EDIT: I only rubbed at full lock in reverse, which I wasn’t going to put up with long term. So I added the spacers to get over it.

 

Anyone running 285/75’s on 4runner trail wheels? My friends selling me a set, I wanna know if I gotta cut the cab mount. He’s got Nitto Terra grapplers on them. So with it being a a/t tire shouldn’t be too bad? Currently got a 2” lift. Ran 285/70 Nitto trail grapplers on 17x8.5 +0 methods no problem. So tryna see how much of a difference 285/75 would be.