OME MT64 height adjustment

Hi everyone!

I'm planning to buy and install the OME MT64 on my 3rd gen tacoma. However, it is not clear how much lift I can gain by adjusting the snapring grooves on the body (see picture). There are 6 positions and I'd like to gain 2" or 2.5" front. Any idea? Thanks in advance for your help!

 

Here is the arb guide if that helps. https://view.publitas.com/arb-4x4-a...nal-application-catalogue-latest/page/232-233
It says to use the top notch to be able to gain 2" of lift depending on the spring and weight you have up front. I just ordered a set for myself with the 4007 springs, I do not have any extra weight up front and am planning on using the 3rd from the top notch. trying to stay at 1.5" of lift up front.

page 281 also has all of the spring specs. looks like they are all the same spring rate just different heights in 5mm increments

 

But it is advertised to be able to be lifted up to 3" of lift so putting it to the top notch would lift my truck more than 2" of lift? I would maybe say 3rd notch with no weight in front maybe?

 

I think you could definately get 3in on a middle setting with the longer coils. Mine were installed today and I got 1.5in in front with the 4007 coils on third from top notch.

Page 288 of that guide has the spring specs.

 

I ordered mine with the 4000 coils as I don’t have any added weight and not planning to add any. Also planning to let it on 2nd notch from the bottom, as advertised for trucks with no added weight and hoping to get 2 niches of lift in the front…what do you think? I don’t have access to the guide your mentioning I found the one I posted on the internet.
How’s the ride so far? What do you think of the set up? Thank you !

 

I think that might be a little bit less than 2 inches. each notch is 5mm different and the spring you chose is 5mm longer than the one I have, so if you want 2 in you might need to use the same notch as me or even one higher? tough to say since everything is so new. I believe the guide image you found is for the 4004 coil, which is 10mm longer than the 4000 coil.

Does the link I posted not work for you? if not you can find it on the arbusa website, if you hover over 'guides' then click 'OME Catalog' it should pop up. page 233 has the 3rd gen tacoma guide.

heres my before and after:

 

This is very nice! I like the stance! Rear blocus or AAL? What’s your expérience on and off-road?

 

AAL in the rear 1.5-1.75 inches of lift. Just got them on yesterday honestly so havent been offroad yet, but love the on road comfort and performance. stiffer than stock but still plush.

 

Nice!

 

Nice! Do you have 265/70/17 or bigger tires?

 

https://www.instagram.com/reel/C9dfRcBS_uh/?igsh=MWRzb3dkenVua2F3bA==
I think that’s your truck brother!

 

haha yes it is. Its the first set of mt64s they have installed so I figured theyd want to post it. and yes 265/70/17 tires, almost look too small now but theyre brand new and I dont want to deal with any trimming so going to probably stay at that size for a while.

 

I came across this article: https://***************/review/arb-ome-mt64-suspension/
When asked, they told me that they could get 2.5" in the front from 2nd notch (from the bottom) and I guess they got the coils 4004. It really is different from what you had with yours this is crazy! I really hope I could get the 2" I’m looking for on the 2nd notch!

 

Looking to go up roughly 2" in the back with this kit then level it with whatever I need in the front