What Have You Done To Your 4th Gen Today?

I was going to purchase the Cali raised ditch light also but asked the question before pulling the trigger. I asked but have not received any confirmation.
check this thread.
https://www.tacomaworld.com/threads...light-bracket-kit.824947/page-3#post-30524435

 

I actually saw someone on Instagram get these so I looked into it.

 

Put on a Prinsu Pro roof rack yesterday afternoon

 

I got the lasfit liners and arb recovery hooks today.

 

Truck looks sick! On the Greenlane site, it says the sliders are 12.5°. But you say 15° on your post. Did they do a custom angle for you? Thanks!

 

Looks great. Just about to order some. Are those flat or the 12.5°. Thanks!

 

Flat. I had the 12.5 on my 3rd Gen and for me flat is way more functional.

 

No problems with ditch brackets and hood struts. Used OEM bolt.

 

I was going to add the redline hydraulic hood struts too. That was my concerns.

 

Center console organizer
(

$22 JKCOVER OEM Fit 2024 2025 Tacoma Center Console Organizer Tray Compatible with 2024 2025 Toyota Tacoma(4th Gen) Accessories ABS Plastic Storage Box（Patented Design）

https://www.amazon.com/dp/B0D38PNGY6?ref=ppx_pop_mob_ap_sh

thanks for posting this link. Mine will be here tomorrow.

 

De-badged the "4x4" and "Tacoma" badges. I also removed "TRD Off Road" stickers, "This vehicle is being tracked" sticker, "This vehicle has airbags" warning sticker from visors, "Do not remove this sticker" sticker from the floor mats, "warning" sticker from glove box, dealership sticker, "This vehicle can roll over" sticker from visors, "Only the owner can remove this sticker" sticker from 14" display center, "Warning" sticker from rear seatbelts, "Don't place your wallet or tablets on the phone charger" sticker, and "Service due at 5,000 miles" sticker. Jesus.

The 3m Stripe Off wheel worked perfectly on the TRD Off Road stickers on the bed. It also worked like a charm on the dealership sticker, and the double-sided molding tape residue from removing the Tacoma badges. Thanks for the advice ladies and gents! After using the 3m wheel, I vacuumed up the eraser particles with a brush attachment, then rubbed each area with Goo-Gone on a paper towel. Then polished the area with a clean paper towel a few minutes later. Zero evidence anything was ever there.

 

I really like this wheel and tire combo. Your truck looks great!

 

I have both. Great choices! Lasfit has been great. Going to Freeman Park tomorrow. I may need the ARB recovery hooks to tow people out. Lots of tourists there.

 

Walker T, how did you go about removing the stickers from the sun visors?
TIA,
Max

 

I removed both of the visors. Just two Phillips head screws, simple. Then I peeled the plastic/vinyl stickers off with my fingernails. This left most of the adhesive on the visors. I sprayed the adhesive areas with Goo-Gone and let them sit for a few minutes, and then started scrubbing with a stiff scrub brush. I vacuumed the adhesive granules up with a shop vac using a brush attachment. Applied more Goo-Gone to any adhesive areas that still were present, and scrubbed again. When all adhesive was gone I dried the visors with some paper towels and left them in the sun to dry out. Worked great.

 

Thanks for the detailed response!

putting that on my list.

 

You might want to apply some heat with heat gun or blow-dryer. This should loosen up the adhesive enough that you won't have that much to remove.

 

Method 703 with a +35 offset on some 285/70/17 installed yesterday

 

Yes! More pics! New wheel and tire day is mandatory 3 pics for all of us droolers. Looks so good. Congrats!

 

Thank you ! These are the only ones I’ve taken so far