Newish member and I come with a puzzle

This is ODD......
How on earth can you have power to only one side of a fuse.
Then flip the fuse over and it then it work??????

WTF is going on here.......?

Is that the SAME fuse that has been in there since it this started?
Maybe try a DIFFERENT fuse?

If it's a different fuse.....I'm kind of lost.

 

No I’ve put 5 new fuses in there and the last time I did it I swapped it with another one so I’m not sure what’s happening here I don’t know if my fuse box just has a loose connection or wtf is happening it so strange Ima have to check it agin once its hot as shit outside agin I have a wire jumper from a old car build and that’s a smidge wider then a normal fuse ima pop that in there and well see what happens

 

It's not possible for one side of a fuse to have power and the other to not if the fuse is intact, are you sure you were making good contact with your tester?

 

Yeah I don’t get it I put it in there moved it around and nothing after flipping it this it tested in top and bottom I don’t understand stand I went back out and checked it and it fired right up agin I’m test it out agin tomorrow in the hot part of the day

 

Update went outside this morning. Truck started right up. Came home from work hot as shit wouldn’t start checked the fuse wasn’t reading very well but I did finally get a reading. Went ahead and pulled the 15 AM. Ignition fuse put it back in truck started right up

 

That suggests to me that there's a connection issue in the box, either with the fuse terminals or in the box itself.

 

I found a replacement box for like 50-60 could pick that up an I guess see if that does it I going to pull the fuse box and see if something
Not plugged in properly etc

 

Power comes in on the 1B plug. (Upper left corner. Above the DR LCK fuse)
I guess you can make sure it is plugged in good, and has good pins/fitment.
Before I hack up my wires going into/out of the fuse box, I'd try a the $60 fuse box
Below you will where power comes in and out, the out side is where you start "hacking" multiple harnesses. (4 different plugs/harnesses)
Sure, you could add your own in-line fuse. But it's going to be ugly. Which is why I'd go for the used fuse box first.
That is, if the connection at the connector is good.

 

Well still waiting for the fuse box to come in but while waiting I went ahead and ordered and replaced the ignition switch. I’m now reading 13.9 at on the 15a ign fuse witch was only reading 13.2 Don’t know that they make a difference or not, but still no check engine light but when I run my scanner on there, I’m still pulling all those oxygen codes

 

Well came home today gave it another shot wouldn’t start till I pulled the 15a ign fuse waited half a min an put it back then she started right up replacement fuse box should be here in the next few days

 

Incabin fuse box swap here we go figured crossed

 

Wow looks like your swapping more than the fusebox

 

Well I was testing all wires an looking for any shorts an checking every ground I could find

 

Update I drove the truck today not to far but to the gas station and to homedepo runs pretty good today wasn’t very hot but I’ll keep yall updated tomorrow I’ll probably start putting a lot of the panels back on after. Good cleaning

 

Okay well I’ve taken the truck out for a errand an she did well so for the past few days I’ve been driving her to an from work etc so I’m thinking it’s she’s fixed although I havnt had super hot day but I’ll take it next issue I need to address is the filler neck for my gas tank it hardly lets me pump gas so something is abit off

 

Still going good

 

Congratulations on fixing the truck. Excellent problem solving from the team

 

Thanks still going strong no issues I’m going to open up my old fuse box to take a look inside and see if something was melted or if it was just a connection issue I also plan on replacing the starter after crankin in the truck for basicly a month lol DM93 and TnShooter really helped save the day if you ask me thank you guys so much I’ll post another update when i open the box

 

Did we fix the AF sensor codes and EVAP codes too?