LED for front turn signal?

I am sick and tired of that awful orange buld on the front for my turn signal. Is there an LED available to replace that?

 

I'm sure there is, but if you do change them out, you'll have that ricer hyper-blinking because the LEDs draw less amperage than regular bulbs and thinks you have a bulb out and thus for the hyper-blinking.

 

Look to the left

http://www.superbrightleds.com/vehicle/2011/toyota/tacoma/62/1052

 

Good website but they only offer the turn signal in yellow.

 

I'm sure the OP is just speaking of the bulb color when off(I think). So an LED would look white when off. As far as actual color. It's okay if it's white when it's on steady, but for actual turn signals, they legally have to be amber when blinking, I believe. They do have switchback LED's which if you had DRL's they would be white when steady on but blink amber with turn signals.

 

Running white 3127 bulbs (non-LED) in mine, the lens is slightly yellow anyway so it comes off as a egg white color. My state requires orange OR white front signals, so I'm in the "clear" (haha) in any case. Nice compromise for me because like you I hated the orange look all the time.

 

do you have day time running lights?

 

here it is this should answer all your questions

http://www.tacomaworld.com/forum/lighting/182744-2nd-gen-led-turn-signals-walk-through.html

 

no

 

check the link i posted i cover almost everything you need to know in there.

it should answer your questions if you still have questions pm i swapped every single bulb on my truck to high power putco leds

 

if i could figure out how to post videos i would show them off lol.

i'm running 6 in total 2 in the arb 2 in the headlights and the 2 in the tails. works like a charm.

 

If you just want to get rid of the orange color then use a chrome bulb so you dont have to change anything. The chrome bulb you cannot see until it lights up. Or just use the white LED's. Check with your inspection station in your state. I'm not required to run orange either. I run white front and back in my Lexus.

http://www.xenonmods.com/chromebulbindex.htm

 

Do whati I did and go buy a rattle can of high temp silver engine paint and spray a light coat over the bulb. This will eliminate the egg yolk look but still let the bulb function and emit plenty of light. I did this mod 6 months ago. You'd never know by the light output of all 4 blinkers that they had a light coat of silver engine paint on them. Now my sterling are still orange but don't have that egg yolk look when off. I do this to all my lights on my vehicles (trucks and motorcycles). Cheap simple fix if your only interested in getting rid of egg yolk effect.

 

$22 3157led.bp2 SYLVANIA - 3157 ZEVO LED White Bulb - Bright LED Bulb, Ideal for Daytime Running Lights (DRL) and Back-Up/Reverse Lights (Contains 2 Bulbs)

3157led.bp2 at advance. Old thread I know but w.e lol, for future peoples looking lol.

 

Sylvania are the worst piece of crap LEDs out there. There are no good LEDs sold at your local auto parts stores.

 

I used these ones. They work great! I’ve had them in for a month and a half with no issues. I had already done the Meso stage 1 kit in the rears. Just like the description says there is no hyper flash and they are very bright. Also gets rid of that “egg yolk” appearance. They only thing I did was heat shrink around the connection to weather proof the wiring.

ENDPAGE 7440 7440NA T20 W21W Built-in Load Resistor LED Turn Signal Light Bulbs, Anti Hyper Flash and CANBUS Ready Error Free, 25W High Power 1000LM Extremely Bright Amber Yellow (Pack of 2)

https://www.amazon.com/dp/B07V829HQF/ref=cm_sw_r_cp_tai_t02MEbQ39SEBQ

 

https://www.vleds.com/shop-bulb-numbers/7443.html
i just bought some of these, they are expensive but there is a "spring" discount, 20 percent off. plug and play, i guess you could just add resistors and pay less for LED bulbs from Amazon etc.