1. Welcome to Tacoma World!

    You are currently viewing as a guest! To get full-access, you need to register for a FREE account.

    As a registered member, you’ll be able to:
    • Participate in all Tacoma discussion topics
    • Communicate privately with other Tacoma owners from around the world
    • Post your own photos in our Members Gallery
    • Access all special features of the site

changing tranny fluid

Discussion in '1st Gen. Tacomas (1995-2004)' started by fireturk41, Apr 12, 2009.

  1. Apr 12, 2009 at 8:12 PM
    #1
    fireturk41

    fireturk41 [OP] I like to break shit!

    Joined:
    Dec 23, 2008
    Member:
    #11857
    Messages:
    4,840
    Gender:
    Male
    First Name:
    Kevin
    High Point, NC
    Vehicle:
    280k miles
    SAS, Locked front rear, Ufab sliders and bumpers, air compressor, 35" BFG KM2 on steelies and 36" TSLs
    can you do it yourself on the first gens? if you can can someone please give instructions and or pics/diagrams thanks
     
  2. Apr 12, 2009 at 8:19 PM
    #2
    chris4x4

    chris4x4 With sufficient thrust, pigs fly just fine. Moderator

    Joined:
    May 8, 2008
    Member:
    #6497
    Messages:
    112,751,539
    Gender:
    Male
    First Name:
    FlimFlubberJAM
    Tenoe, AZ
    Vehicle:
    2019 Rubicon 4 Door,
    4.10 gears, sliders, and lots of buttons.
    Drain the oil from the tranny drain plug. Remove the tranny oil pan. Then, remove and replace with new, the oil strainer. Clean the old gasket material off the pan and surface it mounts to on the tranny. Install ( or make) new gasket/ Fill until the propper level is reached on the dip stick.

    :)
     
  3. Apr 13, 2009 at 4:20 AM
    #3
    Janster

    Janster Old & Forgetful

    Joined:
    Mar 25, 2007
    Member:
    #1138
    Messages:
    14,339
    Gender:
    Female
    First Name:
    Jandy
    Lancaster, PA
    Vehicle:
    2016 GMC Canyon SLT w/ LineX and....
    You have an Automatic?

    I'd recommend having the tranny flushed. And I'm not sure if you can do that at home.... might be better paying someone to do it and ensure its done right.
     
  4. Apr 13, 2009 at 6:47 AM
    #4
    chris4x4

    chris4x4 With sufficient thrust, pigs fly just fine. Moderator

    Joined:
    May 8, 2008
    Member:
    #6497
    Messages:
    112,751,539
    Gender:
    Male
    First Name:
    FlimFlubberJAM
    Tenoe, AZ
    Vehicle:
    2019 Rubicon 4 Door,
    4.10 gears, sliders, and lots of buttons.
    Good advise here. BUT, I have found that most of the time when they flush, being as they dont change the filter, all the shit still sits in either the filter, or is run back into the tranny.

    The absolute best way to change the fluid would be to drop the pan, change the filter, THEN get the flush.

    My $0.02.
     
  5. Apr 13, 2009 at 6:51 AM
    #5
    fireturk41

    fireturk41 [OP] I like to break shit!

    Joined:
    Dec 23, 2008
    Member:
    #11857
    Messages:
    4,840
    Gender:
    Male
    First Name:
    Kevin
    High Point, NC
    Vehicle:
    280k miles
    SAS, Locked front rear, Ufab sliders and bumpers, air compressor, 35" BFG KM2 on steelies and 36" TSLs
    since my truck is so old, should i tell them just to drop the pan and change the filter with no flush? with not knowing when the last change was and at how many miles it was at im afraid a flush would crack the seals
     
  6. Apr 13, 2009 at 7:00 AM
    #6
    chris4x4

    chris4x4 With sufficient thrust, pigs fly just fine. Moderator

    Joined:
    May 8, 2008
    Member:
    #6497
    Messages:
    112,751,539
    Gender:
    Male
    First Name:
    FlimFlubberJAM
    Tenoe, AZ
    Vehicle:
    2019 Rubicon 4 Door,
    4.10 gears, sliders, and lots of buttons.
    Yes. Be sure to ask for the old filter back, so you know they changed it. Tell them you want it so you can send it out to have oil sample performed.
     

Products Discussed in

To Top