Colinb17's kinda sorta build thread - now with 4-link and long travel

You can write in a code for it to read the tranny temp, on auto's only.
It's on the last few pages of AZ geek talk

 

Ultra guage has a pitch and roll gauge?

 

No. Torque does. Torque just uses the pitch and roll sensors in your smart phone/tablet to gauge that. You just just download any pitch/roll app and use that as well. The only issue I find there is you have to lock your phone into place somewhere and then calibrate it on flat ground for it to be accurate. I usually just lay my phone in the cup holders so that doesn't really work out too well for me.

 

I was under the impression that the reason scangauge nor ultragauge could show tranny temp was because the sensor that toyota puts in the tranny is simply a yes/no sensor and not an actual thermometer like for your coolant temp or so forth. so it merely throws out a warning if it gets too high but if not then it is switched off or something like that??? was i lied to?

 

There is a thread on here that shows how to make on of the 2 Brady just listed show an actual temp... I will see if I can find it...

 

i'm just adding an actual gauge for that. i don't always have my phone mounted, but it'd be nice to always see that info.

exactly. you can download any app that has those features. i just like that it's integrated to torque, so all i have to do is swipe my finger to get it to the next screen instead of opening aother app. I mount my phone right next to the screen for my cameras, so i have all of the info in one spot, and the phone is held nice and solid, so once it's calibrated, i get consistant, acurate readings.

 

I'm pretty sure the scanguage can. But I was cheap and didn't want to spend that much for a scanguage. There are ways to make a dash guage that reads tranny temp and I don't recall it involving the install of a temp sensor so I assume there is one in there already.

 

i got frustrated with mine, but it only took me an hour? if that to get everything to fit. once i got the holes lined up and behind the trim, i just screwed it down where it was and it turned out ok

 

i've had a lot of practice with the dremel in the last week

dremel, gauge mount, running the wires down tho the floorboard, and bolting everything up took about 15 minutes. my biggest gripe with it is that that gauge holes were a little too snug couldn't even push the lower gauge in all of the way. had to wollow out the hole with a sanding wheel.

transfering pictures to my computer now.

 

all trimmed and fit with the gauges. you can see the notches i had to make in the handle holes as part of making it fit properly



already lots of wires in the a-pillar 2 power and 2 ground for the 6 roof lights, and the 3rd power and ground are lift over from my old roof rack when i had rear facing lights on the roof. i left the wires so i didn't have to rerun them if i ever needed more power up on the roof for any reason.



2 power harnesses, and the signal harness.











now just have to get everything wired up on the other end.......

 

so what do you plug into your ob2 port then?

 

bluetooth transmitter

http://www.amazon.com/s/ref=nb_sb_n...fix=bluetooth+o,aps&rh=i:aps,k:bluetooth obd2

 

Nice work on the gauges. I had Volts,oil pressure,oil temp and vacumm in my tacoma

 

eventually i'd like to have afr, tranny temp, oil temp, and oil psi in the pillar and steering wheel pods, and then flush mount the volt gauge somewhere in the dash.

you find vacuum to be useful during daily use or wheeling?

 

The IT'S steering wheel pod was a nice setup. I never finished the vacuum gauge was one of the last things I worked on before I sold it.

 

new tundy workin out for you?

 

Yes sir, It's a little hard on gas but that could also be the speed I drive. Makes towing easy I tend to forget I have a trailer with the power of the truck and trailer brakes.

 

glad you're happy with it