New England B.S. Thread

Yup I'm still very interested sir

 

This..I have 2 PIAA fogs and 1 driving, the lens is different.

 

Repost

Sorry i have just been sitting on them lol. If i have time to get these fogs wired, eat diner, then hook up mikes fogs and take pictures and still have time to watch an episode of breaking bad then i will have pictures tonight. If not, i should be able to get to it tomorrow.

 

Hopefully you can get them to work better then I did
I had nothing but issues from day 1 with those .

 

Saw a Silver DBL Cab that had to be on this site. It had a satoshi grill with lights behind it, fog light anytime mod with HID's in them, Black wheels, lift and exhaust (at least a tip). It was near the Sears in Woonsocket. I was at the Shell station.
Maybe they lurk on here.

 

Yeah, I seem to be getting a lot of that today

They likely use the same bulb, not sure if you've confirmed that yet or not. Usually it's the housing that directs the light to make it a driving or fog pattern though. I think you're stuck with what you've got, just a matter of what color you want.

Also, I'm not sure what you got from John, but I have a stock PIAA switch if you want it (that goes for anyone in this thread actually).

I'd blame the electrician

What sort of problems did you have?

 

John gave me the whole wiring harness. But i cut it up because i already have a relay and switch wired. Annddd its not working. I dont feel like troubleshooting it now in the dark so i am ganna go back to it tomorrow. Apparently alot of people have issues with the bulbs blowing out. I read it may have something with the lights grounding themselves to the bumper and nylon washers on the mountinf studs will eliminate the issue. i don't really know what i am talking about tho

 

Talked to Allpro today. The Currie 60's they have are 64" wide for the front and 66" wide for the rear. Measured in WMS (wheel mounting surface). The rear axle is only 1" wider than my stock axle. The front is 64" wide.

BUT! Allpro can have them made for me in any size I need! I was gonna go 4" wider than stock, so I'll get 69" wide axles front and rear. Woot

 

That sounds like a very serious design flaw if that's really what's happening!

 

I bought $30 in cupcakes today. Just in case you guys wanna know.

 

I dunno. A couple members on here claimed the bulbs go every 6 months or so. We will see, first i gatta figure out why my wiring isnt working

 

I had them wire correctly . Blew both bulbs 2 weeks after install . Bought more bulbs decided to cut it up try my own wiring . Blew both bulbs lol wired it back to the way piaa had it and blew one bulb . Now it's Evans . I'm sure he will figure it out .

 

AHAHAHAHAHAHAHA

From the creators of "what does the fox say" comes "Stonehenge"

Sarah literally pissed her pants laughing.
http://youtu.be/mbyzgeee2mg

 

Lol shit. There was a 20 amp fuse in the holder, maybe they were pulling to much power? well maybe good thing i bought extra bulbs.

 

The fuse size doesn't matter until there's a problem. The lights will only pull what they require, the fuse is just supposed to create a failure point. Keep in mind, your headlights have 10A fuses for each bulb and separate fuses for hi and low (4 fuses total, all 10 amp).

John, do you remember if there was space between the housing and the steel opening, like could the housing have been hitting the steel causing the bulb to blow? There should be a little wiggle room between the steel and the housing. The problem with the bulbs blowing might not be electrical.

 

I never changed the fuse . That's what came with it . Iirc I'd look it up on there site to make sure your using the right one

 

Oh my god there's more!

http://youtu.be/PaEnaoydUUo

 

Both bulbs might be blown right now. Just hooked up my light bar, wiring works fine. Except i forgot i had a 15 amp fuse in and it blew after about 2 seconds lol.

 

Oh my god, make it stop!

 

Maybe it has to do with that washer you were talking about