Illumination Supply Light Bar + BAMF Light Bar Mount GROUP BUY

Which version of this switch works with the harness?

http://www.otrattw.com/proddetail.php?prod=VVPZC12-5LB

 

Any switches will work but if you don't want to add any additional wires, the switch listed right below 'Rocker Only' are the ones that will work.

SINGLE LIGHTED SWITCHES

V1D1BC0B -SPST OFF/ON – Red LED

V1D1BN0B-SPST OFF/ON – Amber LED

V1D1BH0B-SPST OFF/ON – Green LED

Upper LED that is ON when the switch is turned ON.
Three terminal switches with no rear barriers. Use 1/4" female disconnects or VCH housing. (Packard terminals for the rear housing are sold separately)

On the drop down there is also a daylight Blue listed for this category that is not on this list but will also work.

 

Any of the the V1D1 switches will work. It just depends on what color you want the LEDs and which LED you want lit up for the dash illumination/ active light.

 

Sweet thanks!!

 

did I make the list in time...

My order please:
1 ea: 20" Double Row (combo)
1 ea: Wiring Harness- Single
1 ea: Wiring Harness- Double
1 ea: BAMF Light Bar Mount (bare)
1ea: Double LED Bar Mount (bare)

Think this will do it.

STANDING BY FOR PM TO CONFIRM!

Thanks!

 

Would I be able to order the dual harness and 2 female deutsch connectors?

EDIT: Would the dual harness power only 2 pods or would they be sufficient to power 2 whole LED bars (20" double row and 15" single row)?

 

Ok, I am not new to LEDs (have a whole house full of the ridiculously expensive bulbs) but I am new to LED light bars. In shopping around I have seen other bars with covers that attach to the front similar to a Hella Spot.

Finally, here comes the question... Do you or your supplier offer one? If not does anyone know where to get a universal one? Understand these are impact resistant, etc, just thinking I may want one.

 

Powder Coated, thanks

 

You heard the man, put in some orders guys! Spread the word.

 

I put a link to it in my signature so that way anywhere I post I'm putting it out there. See below.

 

Can you put me down for a 20" dual spot/flood combo and a single wiring harness?

Are the behind the grill mounts compatible with 1st Gens?

 

Yes we have one for the 1st gens .

 

325W total is what I'd recommend on the wiring harnesses. The 20" Double Row takes 120W, which 15" single row are you asking about?

I believe my supplier carries covers, I'll look into it.

Reservations updated, please message me if you're missing or something looks wrong. Thanks!

 

I have a Blitzpro Hawk 15S that hasn't been installed yet. Looks like total consumption would only be 156 W. I'll take a dual harness and 2 female deutsch connectors. Thanks!

 

Based on existing inventory, I'm going to begin collecting money and shipping out orders for people in the order they reserved in. You'll receive a PM from me with further instructions if you qualify for early fulfillment.

 

Sweet!!

Thanks again Calvin.

I don't know if you forgot to put down one of those female connectors or if you didn't on purpose but I want one of those as well.

 

Thanks once again. If they have them I am interested!

 

Any reason not to go with a double harness, instead of a single, when only ordering one light?

I'm thinking of getting a double, in case I want to expand later.

 

Normally there's a bigger cost difference.

 

Just to verify, the 20" is the one that fits for the mount? If so,

Can you put me down for;

1- 20" Double Row (combo)
1- Wiring Harness- Double
1- BAMF Light Bar Mount (bare)
1- LED Bar Mount (bare)

Thank you!

Is the payment directly to you for both? or the mount and lights seperate?