Sluggo: The 4 banger build

those are the 10" wide version of the wheels I have. Mine are 15x8. Ultra Motorsport En4cer Type 181.

I like mine and they look much better in black IMO.


with the center caps.

 

Lucky! I love those wheels!

If either of you EVER get rid of them I will buy them haha

 

well I'll be damned! Thanks a ton Adam! It's good to know what wheels I have lol!

I'll see what they look like when they get bolted up. Something about the aluminum look really vibed with me.

Haha I'll keep that in mind, however the chance of me getting rid f them is next to zero

 

That's a good find! Plan on shining them up or painting them? Either way, you can't beat an aluminum rim

 

I'll probably just polish them up if I get bored, but they will stay like that for now.

 

They're WIDE. You'll definitely be needing to tub a bunch and trim fenders with those and 35's.

 

I didn't like them as much with the aluminum finish. Also, the surface was corroding and it would have been difficult to get them to look shiny again, which is why I painted mine.

back when my truck was just a little guy like yours.


first round of paint.

 

yea the 10s are wide..probably end up cutting more then me..haha and needing spacers still.

 

Those are sweet! But i agree with painting them. my aluminum wheels get stained really bad from the winters. I need to paint them

 

duly noted I am prepared to tub a lot and cut a lot. The tub job is going to be done the 8th and 9th.

you are a broken record lol. I know that. Im just going to go jon on the truck and build a new fire wall

Im gonna get the tires mounted tomorrow and see just how tight it is with zero hammering or cutting up front for all the curious minds haha (like me)


also, thanks again for the pics adam! Great comparison of the wheels painted vs not! If/when they get bad i bet i take the same route I did before and just derp em.







Also today, I spent more money, I ordered some LED lights, doing some cosmetic touches in my free time

Im doing raptor lights lol



I finally ordered my own air compressor, after 3 years of mooching



I really dread dealing with this, but in the next day or so im going to order a bearing kit for the read so i can swap out the bearings at konstas. If I do that, i might put brady in charge of the tub while konsta and I take on the gears...brady will brobably burn my truck to the ground

http://www.partsgeek.com/gbproducts...+Google+Base&gclid=CP7pnoyI6bwCFYVafgod3mcA4Q


OH YA! I need rock lights too!

 

Oh snap! This could be interesting! I doubt I can burn your truck down, but I can cut too much... haha


I need to do my rock lights. Hell I have a shit load of lights I just need to find the time to get them on.

 

I was kidding haha. I could pull a joe, sombody works on my truck then burns it to the ground. TADAAA! I dont know if konsta would go to the shop or just do the third at his shop. I dont even know if its the bearings. but at this point there isnt much I can think of that would make all this noise and vibes and what not. just replace the bearings and reset the pre load and backlash and tighten everything again.

Just ordered my led rock lights. So those need to get wired up as well

 

could be a U joint...

 

HAHAHAHA

ya, right.

u joints dont make 3 different noises and 2 different types of vibes.

this is a symphony of shit going wrong.

 

Different U joints? haha

mine made an annoying ass rattle/shrieking.

 

I just need to put the go pro over the rear axle and go for a drive on the highway!

 

Which rock lights did you get?

I'm thinking I'm just going to make my own setup...

 

4 strips of waterproof led lights

 

Ah, nice...