Custom Rocker Switch Group Buy - Limited Time! - Ships NOW! - Blitzpro

I need that two switch holder. And measurements. wanting to do in cab winch controls.

 

We can make it in any dimensions your want. PM me what you'd like and we can get started.

 

What if you need a different picture than what you have. I installed under hood LEDs and would like to run the switch inside

 

That's not a problem. We can draw a custom icon for you. If we think there may be others that could use the icon, we won't charge you for the artwork. I recall there's anothe vendor..(Anti Dark I think?) on TW that is selling engine bay hood lights. PM me and we'll work something out.

And just as a side note, we welcome new icon ideas. If you need custom icons, just email or PM us. We're always available to work on new ideas.

 

How do I add the removal tool to my order? It's not an option on the group buy link, want to replace my sPOD covers.

 

I need it to fit beside the cup holder near my shifter. I want to put winch power and in / out switches in it.

 

Sorry, forgot to add it to the item category. Here's the link if you'd like to order the actuator removal tool:

http://mkt.com/bpgb/actuator-removal-tool

 

I have made fairly slim 2 slot panel that measures 66mm x 56mm (~2.6"x2.24"). Has 4mm holes for mounting. The mount holes are spaced 62.4mm (2.44") apart. This about the slimmest bezel we cut for 2 slot panels.

 

Do you offer any switches that will fit into the blanks that are located under the HVAC controls in the center of the dash? They are just a bit smaller than the switches that you have listed in the group buy.

 

Will these work for the first gen rear diff button too? Same way?

 

sub'd

 

I think you're talking about the slots above. Unfortunately, we don't have those available at the moment. If there is enough interest, we can produce a small batch. If you're really interested, we could gauge interest in another thread.

Yes, I believe if you pop out the bezel, the opening is approximately the correct dimensions. You may need to file down the tabs in order to snap in the switch, but I do believe it will be a snug fit.


All of todays order have been packed and shipped! Thanks guys!

 

Awesome! Thanks

 

I am looking to set up some hood lights and some bed lights and those are the only two switch blanks I have available. Out of curiosity, about how much would it cost to special order two switches?

For what it is worth, I have seen more than a few posts from people who have expressed interest in switches that fit that location. So it might be worthwhile to gauge interest with another thread. If you own the TRD Off-Road those will probably be the only blank spots most owners will have to put a switch(s).

 

ship to Canada?

 

Yes we do, however, it's $17.50 for a flat rate USPS padded envelope anywhere in Canada. So it would be the same shipping cost for 1 switch or 16 switches in one envelope. Maybe gather a few buddies and put in one order to save on shipping?

I have fit 16 switches comfortably in a flat rate envelope, however I think I can do 22 switches with proper padding.

 

Is it possible to do custom writing on a switch? I want a switch to disengage my ABS. The top of the switch would say "ABS OFF" and light up when the switch is ON, maybe a symbol or something in the middle, and no writing on the bottom

 

We do have a switch body that will fit that slot. The top of the rocker only illuminates when the switch is in the ON position. I'll take a look if we have stock of any of those bodies and rockers right now. Will keep you posted.

 

Yes! We are all about making your switch fit your application. We can definitely do that. Let me know if the above fits your needs.

 

Out of curiosity, how does the circuit work for disengaging the ABS? Are you going to be grounding a signal to disengage ABS? Or will you be switching a positive signal?