Blue Sea - CUSTOM CNC electrical Panel

EDIT - $200 firm Shipped.


Apparently people feel the need to post their setups in my thread about how there setup is cheaper. This is a unique design, my price is firm if you dont want it or are not interested. Move along. No need to post about your inferior setup.

I need to sell this panel I built. It is in perfect working condition. I want to change the design to include a Low voltage Switch and a few other bells and whistles. As and FYI Based on my RD of the bracket I have over $500 in the Design and build. Please note the comments below.

what you get:
-BlueSea 12 position fuse block -

$27 Blue Sea Systems 5026 ST Blade Fuse Block 12 Circuit with Ground and Cover

http://www.amazon.com/Blue-Sea-Syst...d=1412704066&sr=8-3&keywords=blue+sea+systems
-BlueSea 100AMp breaker

$36 Blue Sea Systems 7087 285-Series Circuit Breaker, Panel Mount, 100A

http://www.amazon.com/Blue-Sea-Syst...=1412704121&sr=1-25&keywords=blue+sea+systems
-BlueSea 80Amp breaker(amplifier) -

$41 Blue Sea Systems 7086 285 Series Circuit Breakers, Panel Mount, 80A DC

http://www.amazon.com/Blue-Sea-Syst...4180&sr=8-10&keywords=blue+sea+systems+80+amp
-Stainless Steel CNC Bracket. - I drew this up in CAD - is has wire managment intergrated in the mount. (new one from Aluminum form Pelfreybilt runs $75, the stainless is $100)
-Mounting Hardware
-Wiring for Fuse panel - 2.5' 4 guage leads with heatshrink and expandable sheath - All stinger HPM wiring.

 

Bump

 

Bump Make an offer.

 

$350 OH MY! id pay about $80-100 for it if your willing to come down to a reasonable price let me know

 

Yea, there is a guy/vendor on here that sells a pretty similar setup for around $120. Sucks you sank all that money into it, but doubt you'll see much in return.

 

Haha $80 to $100 is a long shot.

I have $148 in the blue sea components alone.(feel free to check Amazon)
Another $47 plus in 4 Guage wiring, heat shrink and abs sheath.
Then $300 in fabrication and design cost. (every time we turn ed on the water jet it cost me $50; not to mention material cost)

I can send you recipts on all of this.
I am trying to design a real clean solution for us to have a plug and play setup for us. I personally need and extra circuit breaker, plus I want to change some components to fit a supercharger.

Make me a real offer based on the above. I know I am losing money but $80 is ridiculous. Lol

 

Not to be a dick, but I could show a receipt that I paid $27xxx for my truck but I'm not gonna get $27xxx for it. Like everyone else said, people sell similar systems for cheaper.

But GLWS, free bump

 

Please post a link or pm the link. I believe it's for brackets only.

Mind you this is all brand new.

 

Yah i bought my blue sea box for $50 shipped, circuit breaker for about $12, and wire/connectors/flex loom for about another $25. The panel look almost the same as yours and was made free by a friend but they are sold here for about $60. So essentially this entire setup is under $150 MAX brand new from already established sellers. Im sorry you spent so much in R&D thats a big loss. GLWS though but this may be tough to get more than $150 for. Ill take it for $150 but thats my max offer. Let me know.

 

Can i ask also what is the reason for 2 circuit breakers? I dont understand the concept behind this?

 

IF you want to argue over his price being to high, or bash what hes got take it to PM please. Follow the BST rules.

OP GLWS, looks like a clean unit you built!

 

Not bashing. Sorry if it came out that way. Just stating some facts. No doubt its a good looking setup. Thats why I would personally by it for a reasonable price. And i am still genuinly curious about the dual circuit breakers and how that works. OP if $150 sounds better than my $80 PM me and I can have a buyer for you

 

sent pm

As far as the R&D it is about the fun for me. I am not worried about that. I just want to get a reasonable amount. i have alot of money in this. I am going to turn around and sink more money into a new bracket. My wife wont let me start designing more pieces until I sell this one.

 

$140 in total for my set up. GLWS

 

Thanks for the input. However I want to note the following:
- Your wiring is not as clean, nor does it appear to be professionaly crimped.
-your design has no drip leads or any way to reduce water pooling around your wiring. the design I created allows this. (ie the wiring is directed towards the ground. the panel sits at a slight angle to remove water quickly. they breakers are positioned to allow any water to drip off.
- You only have 2 componets in line with my whole bracket setup. Not to mention, no integrated cable managment.
- your bracket is aluminum mine is stainless steel
- my wiring is high quality Stinger HPM - based on the picture yours looks like generic wiring. (not a big deal just a point.

I appreciate your addition to my sale thread. Your wiring does look well routed. good Job on your setup.

 

I added this to include a Circuit breaker for my ampliphier for my stereo.

 

You say your price is firm? I thought you were 'Asking' $250.00

You did not get thread jacked...calm down. Why are you so threatened by eyesurfs setup that you feel the need to tear apart his setup and imply that his set up is junk...It's not. Get real. If your goal is to build a better pannel than your first one in order to market them to the same members on the same forum where you are being a jerk, I don't see you making very many sales- not to mention; the backlash you are seeing is partially due to you trying to recoup your butt hurt 'R & D' costs in the price of your one self admitted inferior proto-type.

 

OP. Does this fit on ATRAC equipped Tacos?

The hate is strong in this thread. I don't understand why people cant just discuss pricing in private. It's just common courtesy. Don't like the price? Move along. Let the buyer decides for himself and responsible for his own market research. Feel the need to compare products? Do it in the appropriate forum, this is a classifieds section.

 

thank you! yes it does as I have ATRAC on my truck.

 

Its annoying that people feel the need to post their setups in my for sale thread. I am not threatend, I have a cost associated with the bracket. Its not about what the market has available. Its about this being a differnet custom version. they are not the same in any way. I was explaining the difference of my design over his bracket.(yes I was a tad annoyed so i backlashed, wouldnt you) Also, not trying to be a jerk. There are better avenues than a forsale thread for product discussion and price. I am not trying to market or sell these. I made this for my personal use. I gave the CAD file to Pelfreybilt(feel free to ask Pelfreybilt.) I do not want to sell this to the masses, nor made the intention(which you infered) Also please note I am not butt hurt, I knew this would cost me money for R&D, my intent was to brunt the cost of the R&D for the good of the forum not myself. I prefer to help others out when I can. I think you can look up several other thread on this bracket that i created to know i am true in what I say.