**Parts Temporarily Unavailable** Small batch Bussmann RTMR 5relay-10fuse

Had my dash apart 2x, but I have my fuse box up and running!

 

are these switched power or switched ground?

 

If you're referring to the relays, they are connected as shown. The main power and ground into the box can be setup anyway you want, but typically straight to the battery.

 

yep, was talking about the relays. So fuse to 30, aka switched power. Thanks for the info

 

PM's sent with tracking for shipped boxes

 

Sorry for the delay. I've been so busy getting ready for Overland Expo that I've forgot to post. The 5th list is complete (got a local pickup still). This is going on hold until I get back from the Expo and I can sort out the next lists. If you'll be at Expo find me and I can show off my box.

 

where did you get that dash mat?

 

Hm... what's your timeline on these (aka how long is the expo?). I was going to order all the stuff to put one of these together but it'll be 100x easier to just buy it premade. Let me know below is what I'm looking for:
Standard setup with the 80Amp breaker - I can paypal now - just let me know.

Just a quick question when running the relays to the switch would I run 5-12v power to the switch then take the negative from the switch to the 'switch line' coming off the relay?

 

The Expo is Thurs-Sun. I'll take a couple days after to get back to regular programming.

The relays need 12v (10-14v) sent from a switch to the Coil side of the relay. The relay is already pre wired (on my boxes) for ground. All you have to do is hookup:
12v switch IN to relay
12v Acc OUT to Accessory
and
Battery Pos
Battery Neg

 

Sounds good - I'll PM you now to get my name down. Do I need to wait for another 5 person list to fill or is this something you might have already?

 

There is a good 6th and maybe 7th list already building.

 

Wired up just like the tutorial that @tacozord wrote, right?
https://www.tacomaworld.com/threads/diy-build-and-install-a-bussmann-rtmr-fuse-relay-block.399454/

 

Yea, that's just soooo much to dig through lol.

 

It is a lot of reading, I must have gone through it all a half dozen times before I decided to pay for a build. Of course, since I've done that, I went and bought all the parts and supplies to finish off the install in the same manner he did, so I might as well have just built my own box too. Oh well. When it's all done and installed, I'll have a nice custom harness for all of my accessories and a switched (solenoid) aux fuse block driving it all.

 

Amazon, don't have a link, on my cell phone right now.

 

It gets confusing where I am in the mix and when I might have the product at my door. Do you have a ball park estimate so I can somewhat plan?

 

Ok, since there is some confusion here is how the lists stand (unless I mistakenly forgot someone). No pm's have been sent or payment collected for these lists yet. I will be at Overland Expo East. I'll take a couple days after to get back to regular programming. Once I am back ontop of things I will send PMs, collect payment, and order parts. I am not going to give any exact dates because things come up, like this Hurricane and the Tropical Storm following it, shipping delays, work schedule, and life events.

6th list (holding pattern)
1. @SAC-CA-Runner
2. @Robmonster117
3. @OCtaconoob
4. @will.carroll7
5. @ACEkraut
6. @Adventurous

7th list (pending 6th list)
1. @turbodb
2. @mudnrox
3. @Bruce988jl

 

Thanks for the update! I'm in no rush so if someone is impatient you can ship mine 6th instead of 1st. Doesn't bother me. I know you're busy and things come up so I completely understand. Have fun at the Expo and stay safe this hurricane season. Cheers!

 

No rush here take all the time you need. going to be a while before ill be doing more mods to the truck. Just let me know when payment is needed and ill send it out