Sway Bar Links

Disclaimer- Please read this carefully! (Moved 3/1 to a more visible location)
*Please allow 3-5 business days for delivery*
*Please note these are an aftermarket product, that are intended for off-road use*
*They are to be installed at the owners discretion, and the owner will assume all risk*
*The builder is not responsible for any damage to any vehicles during the installation or use of these products*
*It's the buyers responsibility for securing any loose parts when the links are removed*
*No used links will be returned*
*1 year warranty on all links (cost after 1st year)
*All sales are final*
*By purchasing these links, you understand and assume all risk*


These links will work on lifts up to 3", and add an additional 1" to the overall length. The links are over sized, a lot stronger than OEM, and NO DRILLING IS REQUIRED.

I'd like to give some information on the double disconnects and getting them disconnect. First off, please do not over tighten the top bushings. Over tightening the top bushings will cause you to not be able to release the top pin. If you wrench down on the bushings, you will not be able to slide the heim off the stud.

Heim Joint Links
3rd Gen 4runner Links:


4th & 5th Gen 4runner, FJ Cruiser, GX, and Tacoma Links:


Forged Ball Joint Links
3rd Gen 4runner Links:


4th & 5th Gen 4runner, FJ Cruiser, GX, and Tacoma Links:


Custom Powder Coat Links:








PLEASE READ BELOW FOR PRICING, AND KNOW WHAT YOU'RE ORDERING WHEN YOU ORDER IT!
Pricing
*Heim Joint Links - $170 for front or rear; $220 for front and rear
*4th and 5th Gen Disco's - $220 for front; $270 for front and standard rear
*Powder Coated - +$20
*Heim Boots - +$10-$30

*Forged Ball Joint Links - $190 for front or rear; $250 for front and rear

Thanks,
Mike

 

bruh.

Base Pricing Needed..

 

"When" I have a special pricing will be posted there. Normal pricing is posted in the first post.

Mike

 

This part is what I was referring to, "Base Price":

Pricing:*$150 Standard plus options

Please PM me if you're wanting to place an order.

Regular Pricing wasn't in OP, I wasn't referring to a sale price.

 

Glad you were able to find the pricing.

Mike

 

Ahh, okay I see. Yeah I was referring to base price, not sale price. Thanks for the clarifications

 

No worries.

I posted a two sets of links that are on sale in the second post.

Mike

 

In the image shown with them on the truck, those links don't mount like my 1st Gen Tacoma links mount so I'm guessing this is for 2nd and/or 3rd Gen Tacomas? Or is one end not connected and currently flipped upwards in a "disconnected" position...? Cause they almost look like they would work for 1st Gens...

Would sure be nice to find something nice for the 1st gen...

 

Those are the same as a 4runner, and I make a ton of those. The hammered grey tubes cost more, but you get the idea.



Mike

 

Actually, I just figured out while searching around that there are two different versions for the 1st Gen Tacoma... 95.5-2000 are just like the 3rd Gen 4Runner ones like you've got there, but then the 2001-2004 ones are different. They are balljoints on both ends, which would be similar to what you're showing on the first post in this thread.

 

Correct. The 4runner and Tacoma both use the same links, and lengths.

 

Only for 95.5-2000 1st Gen Tacoma.

So then I'm guessing you don't have a solution for the 2001-2004 1st Gen Tacomas with the dual ball-joint style links?

 

The ones for the 01-04 Tacoma's are the same as what's above, and they're used on everything post 04 as well. They're the same as the 4th & 5th 4runner's, and FJ Cruisers. The earlier ones work on 3rd Gen 4runner's, and pre 01 Tacoma's. No matter what I have you covered.

Mike

 

@mstudt - Thanks for your patience and explanations.

 

No problem.

 

Can you disconnect these at the Heim joint and let the sway bar hang?

 

I'm probably going to buy a set soon since I had to cut the threads on one of my links to take it off, and I'm going to put it back on again. The price is per pair right?

 

Sure thing. Shoot me a PM when you're ready.

Mike

 

No quick disconnects tho...

 

I have some of those as well. I'll have to find some pictures when I get home though.